iCAx开思网

标题: UG NX POST BUILDER [打印本页]

作者: afei 时间: 2002-12-6 09:39
标题: UG NX POST BUILDER
哪位大哥有UG NX POST BUILDER MANUAL，请贴一下。18 19的也行。

作者: afei 时间: 2002-12-6 13:31
怎么，没人知道？！

作者: QiuXu 时间: 2002-12-18 11:43
我给你
%
G40 G49 G17 G80 G90 G54
G91 G28 Z0.0
S2000 M03
G00 G90 X0.0 Y-54.388
Z50.
Z1.
Z.803
G01 Z-.197 F500. M08
Y-46.388
G02 I0.0 J46.388 F800.
G01 Y-54.388 F2500.
Z-.394 F500.
Y-46.388
G02 I0.0 J46.388 F800.
G01 Y-54.388 F2500.
Z-.591 F500.
Y-46.388
G02 I0.0 J46.388 F800.
G01 Y-54.388 F2500.
Z-.788 F500.
Y-46.388
G02 I0.0 J46.388 F800.
G01 Y-54.388 F2500.
Z-.984 F500.
Y-46.388
G02 I0.0 J46.388 F800.
G01 Y-54.388 F2500.
Z-1.181 F500.
Y-46.388
G02 I0.0 J46.388 F800.
G01 Y-54.388 F2500.
Z-1.378 F500.
Y-46.388
G02 I0.0 J46.388 F800.
G01 Y-54.388 F2500.
Z-1.575 F500.
Y-46.388
G02 I0.0 J46.388 F800.
G01 Y-54.388 F2500.
Z-1.772 F500.
Y-46.388
G02 I0.0 J46.388 F800.
G01 Y-54.388 F2500.
Z-1.969 F500.
Y-46.388
G02 I0.0 J46.388 F800.
G01 Y-54.388 F2500.
Z-2.166 F500.
Y-46.388
G02 I0.0 J46.388 F800.
G01 Y-54.388 F2500.
Z-2.363 F500.
Y-46.388
G02 I0.0 J46.388 F800.
G01 Y-54.388 F2500.
G00 Z50.
G28 G91 Z0.0
M05 M09
M30
%

作者: QiuXu 时间: 2002-12-25 15:45
这个配置有极大的错误，请大家别用！！！！

作者: 221081 时间: 2002-12-25 18:38
請問各位大哥﹐有沒有UG NX有書啊﹗
       謝謝各位﹗

作者: mr.shang 时间: 2002-12-25 21:31

221081 wrote:
請問各位大哥﹐有沒有UG NX有書啊﹗
謝謝各位﹗

18版的先看看吧

作者: FQG_HI 时间: 2002-12-27 23:45
请问一下我用POST BUILDER做出来的后处理没有 “F“ 呢，我还想在文件头加上刀具的信息那应该怎样做呢？

作者: LONGSNAKES 时间: 2003-6-23 18:35
用PB来作BA，ADD BLOCK OR USER MESSAGE

作者: LONGSNAKES 时间: 2003-6-23 18:39
帮助文件里面有，除非你没有DOCMENTT0atION

作者: xjl251 时间: 2003-6-23 21:32
UG18CAST 里的POSTBUILDER倒有不过很不详细不知道要不要

欢迎光临 iCAx开思网 (https://www.icax.org/)