标题: VERICUT6.2.2对于X3与X3MU1的一些注意事项 [打印本页] 作者: 0203cj 时间: 2009-4-4 08:36 标题: VERICUT6.2.2对于X3与X3MU1的一些注意事项 Mastercam-to-VERICUT Interface (MCAMV)
A new feature, "Put operations in a single VERICUT setup", on the MCAMV Options
window, enables you to put the selected MasterCAM operations into one VERICUT
setup. Toggle "on" (checked) to put operations into one VERICUT setup. Toggle "off" to
put each MasterCAM operation in a separate VERICUT setup.
"Browse" buttons are added to simplify the selection of Part STL Files and Fixture STL
Files on the MCAMV main window.
MCAMV is enhanced to support multiple VERICUT G-Code tables. A new group of
features "VERICUT GCode Table" on the NXV Options window enable you to specify:
Table Name – Select Work Offset, Base Work Offset, Program Zero, or None from
the pull-down list.
Register Number – Enter the register number.
'From' Component — Select the name of the component that represents the "from"
point for determining the offset from the pull-down list. VERICUT will use the origin
of the specified component.
'To' Csys — Select the name of a CSYS to represent the "to" point for determining
the offset from the pull-down list. VERICUT will use the origin of the specified
CSYS.
Tool numbers created and passed through MCAMV to VERICUT now match the tool
numbers defined in MasterCAM X3. Due to differences between MasterCAM X3 and
MasterCAM X3 MU1, the following environment variable must be set as described
below to ensure that tool numbers are created and passed correctly through MCAMV to
VERICUT. Set the environment variable in the .bat file that you use to start MasterCAM
or set it using the Microsoft Control Panel > System > Advanced tab > Environment
Variable feature.
If you are using a MasterCAM part file created using the initial version of MasterCAM
X3, set the environment variable CGTECH_MCAMV_TLNO_IS_SLOT equal to 1as
shown below:
set CGTECH_MCAMV_TLNO_IS_SLOT=1
If you are using a MasterCAM part file created using MasterCAM X3 MU1 or later, do
not use this environment variable (or set it to 0).
主要是set CGTECH_MCAMV_TLNO_IS_SLOT=为1和0的注意点。
呵呵，现在的功能又增加了几个，有兴趣的可以用来对HSM刀路过切的检测作者: 0203cj 时间: 2009-4-4 08:37 UGS的也放这里好了
NX-to-VERICUT Interface (NXV)
Turning tools are now oriented correctly when passed to VERICUT through NXV.
A "Browse" button is added to the Output Directory feature on the NXV main window to
simplify specifying the directory to receive NXV files. This feature is implemented for
Windows only. It is not possible to implement for UNIX.
NXV now exports tools from NX correctly for situations where "Operation Navigator -
Program Order" includes one or more sub-directories with the tool definitions.
NXV is enhanced to support multiple VERICUT G-Code tables. A new group of features
"VERICUT GCode Table" on the NXV Options window enable you to specify:
Table Name – Select Work Offset, Base Work Offset, Program Zero, or None from
the pull-down Table List or enter a name in the Table Name text field.
Register Number – Enter the register number.
'From' Component — Select the name of the component that represents the "from"
point for determining the offset. VERICUT will use the origin of the specified
component. Select from the pull-down 'From' List or enter the name in the 'From'
Component text field.
'To' Csys — Select the name of a CSYS to represent the "to" point for determining
the offset. VERICUT will use the origin of the specified CSYS. Select from the pulldown
'To' List or enter the name in the 'To' Csys text field.
Tool features are now correctly passed to VERICUT through NXV when using NX4.
NXV is enhanced to enable transferring NX turning data (turning tools, stock from a 2D
profile, design from a 2D profile, CLS NC program) to VERICUT.
A new checkbox "Transfer All Coordinate Systems" is added to the NXV Options
window enabling all NX coordinate systems associated with current NC program to be
passed to VERICUT. When toggled "off", only the coordinate systems required by
VERICUT (PROGRAM_ZERO and ***STOCK***) will be transferred.
Environment variable CGTECH_NXV_OUTPUTDIR is added to enable specifying a
default output file. Example of use:
set CGTECH_NXV_OUTPUTDIR=C:\Documents and Settings\Username.
NXV determines the default output directory according to the following rules:
1. If the environment variable is set, its value is used as the default output directory.
2. If the environment variable is not set, the value saved in the NX model is used.
3. Finally, if neither of the above is used, the directory containing the NX model is
used.
NXV is enhanced to enable passing multiple NX fixture models to VERICUT as
individual STL models.
A new feature "Attach Component List" is added to the NXV Options window to
simplify the specification of the Attach Component Name. Attach Component List
enables you to select the desired Attach Component from a pull-down list. The pull-down
list contains all of the Attach Components contained in the machine referenced by the
specified Setup Template.
NXV is enhanced to more accurately pass the following types of NX tool features into
VERICUT.
• When the NX Tool Insertion - (OS) Offset feature is used to specify how far the
Holder overlaps the Cutter.
• NX User Defined tools.
• Counter sinks created in NX under their "hole making" category.
NXV is enhanced to support the NX center drill definition.
NXV now correctly passes NX defined step drills into VERICUT.
NXV now correctly passes NX4 APT 7 parameter drilling tools to VERICUT.作者: 87915156 时间: 2009-4-4 09:26
基本不用这个.估计用的也不多作者: lanqiao839 时间: 2009-4-4 10:08
老大 你能把他弄成方块字么？？ 全是那 e文章吗 看到啊作者: Lance 时间: 2009-4-12 20:05
请问楼主如可在Vericut内设置五轴机床摆头的旋转中心?
我做了个DMU60的五轴机床,就是B轴摆头旋转时,旋中心不在我理想的位置,不知如何调整,请网友指教.作者: Lance 时间: 2009-4-12 20:10
file:///c:/1.jpg作者: Lance 时间: 2009-4-12 20:12
[attach]905080[/attach]作者: 800315 时间: 2009-8-30 08:29 7#Lance作者: flyboat 时间: 2009-10-31 09:35
调整B轴摆头的组件原点到你所希望的旋转中心位置。（你还需要调整它的模型原点）
UGS的也放这里好了