iCAx开思网

标题: 有关于过滤后的程序还是没有圆弧。 [打印本页]

作者: tjhfanuc 时间: 2008-7-28 00:42
标题: 有关于过滤后的程序还是没有圆弧。
不知道为什么，，
  我用的是mastercam9.1sp2版，但是编出来的程序没有圆弧，我用的是2：1的过滤，，可是程序在机床上用时，，机器走的很慢，，这是我现在用的后处理。。
spaces    : 1    #Number of spaces to add between fields
omitseq    : no #Omit sequence numbers?
seqmax    : 9999  #Max. sequence number
arcoutput : 0    #0 = IJK, 1 = R no sign, 2 = R signed neg. over 180
arctype    : 2    #Arc center 1=abs, 2=St-Ctr, 3=Ctr-St, 4=unsigned inc.
breakarcs : 2    #Break arcs, 0 = no, 1 = quadrants, 2 = 180deg. max arcs
do_full_arc : 1    #Allow full circle output? 0=no, 1=yes
helix_arc : 1    #Support helix arc output, 0=no, 1=all planes, 2=XY plane only
compwarn : 1    #Warn if cutter comp applied on arc, 0=no, 1=yes
miscerror : 0    #Error out if Misc Values button is disabled, 0=no, 1=yes
maxrad    : 999 #Maximum arc radius
hel_2100 : no #Acramatic 2100 style helical moves, 0=no, 1=yes
usecanned : yes #Use canned drilling cycles?  Set to no for long output.
force_dpts  : no #Force XY output on all drilling lines including cycle call?
haas_drill  : 0    #Haas style peck drill, 0=no, 1=yes
wcstype    : 2    #0 = G92 at start, 1 = G92 at toolchanges, 2 = G54, 3 = Off
force_wcs : yes #Force WCS output at every toolchange?
stagetool : 0    #0 = Do not pre-stage tools, 1 = Stage tools
tool_table  : 1    #Tool table, 0=no, 1=yes, 2=Predator VCNC, 3=MetaCut View #
output_z : yes #Output Z Min and Z Max values (yes or no)
cool_zmove  : yes #Coolant off with last move
use_pitch : 0    #0 = Use feed for tapping, 1 = Use pitch for tapping
tap_feed : 0    #0 = 2/1 (in/mm) decimal places, 1 = 4/3 (in/mm) decimal places
maxfeedpm : 500 #Limit for feed in inch/min
maxfeedpm_m : 10000 #Limit for feed in mm/min
use_gear : 0    #Output gear selection code, 0=no, 1=yes
max_speed : 10000 #Maximum spindle speed
min_speed : 50 #Minimum spindle speed
sextnc    .NC    #NC extension override
vmc       : 1    #0 = Horizontal Machine, 1 = Vertical Mill
rot_on_x : 0    #Default Rotary Axis Orientation, See ques. 164.
                  #0 = Off, 1 = About X, 2 = About Y, 3 = About Z
rot_ccw_pos : 1    #Axis signed dir, 0 = CW positive, 1 = CCW positive
ret_on_indx : 1    #Machine home retract on rotary index moves, (0 = no, 1 = yes)
index    : 0    #Use index positioning, 0 = Full Rotary, 1 = Index only
ctable    : 5    #Degrees for each index step with indexing spindle
one_rev    : 0    #Limit rotary indexing between 0 and 360? (0 = No, 1 = Yes)
lock_codes  : 0    #Use rotary axis unlock/lock M-Codes? (0 = No, 1 = Yes)
use_frinv : 0    #Use Inverse Time Feedrates in 4 Axis, (0 = no, 1 = yes)
maxfrdeg : 2000  #Limit for feed in deg/min
maxfrinv : 999.99#Limit for feed inverse time
frc_cinit : 1    #Force C axis reset at toolchange
ctol       : 225 #Tolerance in deg. before rev flag changes
ixtol    : .01 #Tolerance in deg. for index error
frdegstp : 10 #Step limit for rotary feed in deg/min

作者: jintjint 时间: 2008-7-28 09:51
后处理选择有问题，选默认的Fanuc试一试。。。

作者: tjhfanuc 时间: 2008-7-28 12:53
标题: 回复 2楼 jintjint 的帖子
我试了，，
还是一样的啊。。没有改进啊。
我一般用的角度是45度。。

作者: huanglonghl 时间: 2008-7-28 21:17
mc里面平行走曲面除了0,90,180,270其他角度过滤没用的

作者: wudliang 时间: 2008-7-28 22:02
你能说说你的机床什么时候生产的吗？

作者: tjhfanuc 时间: 2008-7-29 01:46
标题: 回复 5楼 wudliang 的帖子
J是现在的新的机器啊……
FANUC,,,,,,,,和，三凌的啊。。

作者: tjhfanuc 时间: 2008-7-29 01:47
标题: 回复 4楼 huanglonghl 的帖子
那有什么办法吗……

作者: 进明 时间: 2008-7-29 14:08
平行走45度怎么可能会有圆弧?

欢迎光临 iCAx开思网 (https://www.icax.org/)