iCAx开思网
标题:
【原创】【分享】PM系列培训之二~三维偏置+参考线, Surfcam做法
[打印本页]
作者:
sinderal
时间:
2003-10-7 14:33
标题:
【原创】【分享】PM系列培训之二~三维偏置+参考线, Surfcam做法
在那邊可參考
https://www.icax.org/viewthread. ... 3D1&page=3#pid=
IGS
作者:
sinderal
时间:
2003-10-7 14:34
Surfcam 3D Offset w/ Boundary
作者:
sinderal
时间:
2003-10-7 14:35
Surfcam Planar w/ Flow Surface, Enabale HSM
作者:
sinderal
时间:
2003-10-7 14:36
回來再貼 教程
作者:
laopu_sd
时间:
2003-10-7 15:33
作者:
sinderal
时间:
2003-10-7 16:11
先用Create --> Spline --> Surface Spline 提取 邊界曲線
作者:
sinderal
时间:
2003-10-7 16:11
取出了 紅色 的 邊界曲線
作者:
sinderal
时间:
2003-10-7 16:20
選 3D Offset 選取 藍色曲面,
設定參數, 再選 外邊的 紅色曲線當邊界
作者:
sinderal
时间:
2003-10-7 16:21
就素這種路逕
作者:
sinderal
时间:
2003-10-7 16:25
在 高度100mm 位置建立一個平面, 再將先前 取出的 紅色邊界曲線 投影上去, 建立 新的曲線, 再 曲線 中心位置 建一小圓(R0.5),
Create ---> Surface --> Cross Section --> Section
建成 綠色的 Flow Surface
作者:
sinderal
时间:
2003-10-7 16:27
NC --> 3 Axis --> Planar
選 要切的 藍色曲面
設定參數, Enable High Speed Machining
選 綠色的Flow Surface
選 外邊的紅色邊界曲線
作者:
sinderal
时间:
2003-10-7 16:28
就素 這個刀路
作者:
sinderal
时间:
2003-10-7 16:50
每個 Step間 自動建小圓弧連接
Kao! 跟老美反應要求有螺旋刀路 不接刀的 Patten, 不 鳥 偶
作者:
vip
时间:
2003-10-19 22:48
怎么版主你的SURFCAM2003是中文版的?
还是用汉化软件汉化了?
另我觉得象这种刀路好象没必要弄的这么繁杂,直接用3 Axis的PLANAR铣不更方便吗?
作者:
sinderal
时间:
2003-10-20 10:07
1. 偶在測試啊..正式出版之前
2. 只是單純用Planar, 出來的 東西 不倩啊...
作者:
veteran
时间:
2004-9-8 11:18
呵呵
又学一招
作者:
vip
时间:
2008-2-28 10:40
老大,俺觉得当斜面比较平时这种走法好象还不好,出来 的效果就象台阶,一级一级的,
作者:
oneson136
时间:
2014-1-31 09:12
來跟老哥學習一下了
作者:
k740329
时间:
2015-9-11 00:19
作者:
576463434
时间:
2015-9-11 11:08
谢谢了
欢迎光临 iCAx开思网 (https://www.icax.org/)
Powered by Discuz! X3.3