iCAx开思网

标题: 急求cimit后处理格式如下，QQ：296091910 [打印本页]

作者: fuxiaoyong1989 时间: 2009-7-31 23:59
标题: 急求cimit后处理格式如下，QQ：296091910
%
O0003
(PROGRAM NAME - 3)
(DATE=DD-MM-YY - 22-11-08 TIME=HH:MM - 10:33)
N100G21
N102G91G28Z0
N104G0G17G40G49G80G90
(TOOL - 4 DIA. OFF. - 4 LEN. - 4 DIA= 8.)
(  DIA= 8. R=0.)
N106T4
N108M6
N110T5
N112G0G90G54X-47.1Y-23.28S3000M3
N114G43H4Z10.M8
N116G98G81Z-2.R3.F200.
N118X-11.Y-23.4
N120X-34.4Y-65.09
N122G80
N124M5
N126G91G28Z0.M9
N128M01
(TOOL - 5 DIA. OFF. - 5 LEN. - 5 DIA= 6.3)
(  DIA= 6.3 R=0.)
N130T5
N132M6
N134T7
N136G0G90G54X-11.Y-23.4S1200M3
N138G43H5Z10.M8
N140G98G83Z-64.R2.Q3.F80.
N142G80
N144M5
N146G91G28Z0.M9
N148M01
(TOOL - 7 DIA. OFF. - 7 LEN. - 7 DIA= 8.5)
(  DIA= 8.5 R=0.)
N150T7
N152M6
N154T6
N156G0G90G54X-47.1Y-23.28S800M3
N158G43H7Z10.M8
N160G98G83Z-91.R2.Q3.F120.
N162X-34.4Y-65.09
N164G80
N166M5
N168G91G28Z0.M9
N170M01
(TOOL - 6 DIA. OFF. - 6 LEN. - 6 DIA= 11.1)
(  DIA= 11.1 R=0.)
N172T6
N174M6
N176T4
N178G0G90G54X-47.1Y-23.28S600M3
N180G43H6Z10.M8
N182G98G83Z-91.R2.Q3.F130.
N184X-34.4Y-65.09
N186G80
N188M5
N190G91G28Z0.M9
N192M01
(TOOL - 4 DIA. OFF. - 4 LEN. - 4 DIA= 8.)
(  DIA= 8. R=0.)
N194T4
N196M6
N198T4
N200G0G90G54X-9.925Y-23.9S5000M3
N202G43H4Z10.M8
N204Z2.
N206G1Z-2.2F1000.
N208G3X-9.425Y-23.4R.5
N210X-11.Y-21.825R1.575
N212X-12.575Y-23.4R1.575
N214X-11.Y-24.975R1.575
N216X-9.425Y-23.4R1.575
N218X-9.925Y-22.9R.5
N220G0Z10.
N222X-43.65Y-23.78
N224Z2.
N226G1Z-2.2
N228G3X-43.15Y-23.28R.5
N230X-47.1Y-19.33R3.95
N232X-51.05Y-23.28R3.95
N234X-47.1Y-27.23R3.95
N236X-43.15Y-23.28R3.95
N238X-43.65Y-22.78R.5
N240G0Z10.
N242X-30.95Y-65.59
N244Z2.
N246G1Z-2.2
N248G3X-30.45Y-65.09R.5
N250X-34.4Y-61.14R3.95
N252X-38.35Y-65.09R3.95
N254X-34.4Y-69.04R3.95
N256X-30.45Y-65.09R3.95
N258X-30.95Y-64.59R.5
N260G0Z10.
N262M5
N264G91G28Z0.M9
N266M30
%                                                          红色部分，要不要无所谓》

作者: zbhouin 时间: 2009-8-1 02:05
刚改的后处理

作者: fuxiaoyong1989 时间: 2009-8-1 13:56
%
O0999
G21
G91 G28 Z0.
G00 G17 G40 G49 G54 G80 G90
T01 ( D80R0.8 )
( TOOL: D= 80. R= 0.8)
M6
T10
G0 G43 H01 Z50. S1100 M3
G00 X73.2 Y0.0 Z10. M8
Z1.
G01 Z0.0 F450
X28.2 F900
X-28.2
X-73.2
G00 Z10.
M5
G91 G28 Z0.0 M9
M01
T10 ( 20R0.8 )
( TOOL: D= 20. R= 0.8)
M6
T04
S2200 M3
X39.2 Y-38.3
Z1.
G01 Z-21. F1100
X24.2 F2200
X-20.2
X-27.9
G02 X-35.042 Y-35.342I0.0J10.1
G01 X-35.342 Y-35.042
G02 X-38.3 Y-27.9I7.142J7.142
G01 Y27.9
G02 X-35.342 Y35.042I10.1J0.0
G01 X-35.042 Y35.342
G02 X-27.9 Y38.3I7.142J-7.142
G01 X-20.2
X24.2
G02 X31.342 Y35.342I0.0J-10.1
G01 X35.342 Y31.342
G02 X38.3 Y24.2I-7.142J-7.142
G01 Y-24.2
G02 X35.342 Y-31.342I-10.1J0.0
G01 X31.342 Y-35.342
X20.735 Y-45.948
G00 Z10.
M5
G91 G28 Z0.0 M9
M01
T04 ( ZD3 )
( TOOL: D= 10. R= 0.0)
M6
T05
S1200 M3
G98 G81 X-23.55 Y-23.55 Z-1.8 R1. F80 M8
X23.55
X0.0 Y0.0
X-23.55 Y23.55
X23.55
G80 Z10.
M5
G91 G28 Z0.0 M9
M01
T05 ( Z22 )
( TOOL: D= 10. R= 0.0)
M6
T08
S500 M3
G98 G83 X0.0 Y0.0 Z-25. R1. Q3. F100 M8
G80 Z10.
M5
G91 G28 Z0.0 M9
M01
T08 ( Z3.3 )
( TOOL: D= 10. R= 0.0)
M6
T10
S1810 M3
G98 G83 X-23.55 Y-23.55 Z-13.5 R1. Q2. F80 M8
X23.55
Y23.55
X-23.55
G80 Z10.
M5
G91 G28 Z0.0 M9
M01
T10 ( 20R0.8 )
( TOOL: D= 20. R= 0.8)
M6
T03
S2100 M3
G00 Z10.
X-0.1 Y0.0
Z1.
G01 Z-11. F450
X8.95 F1500
G03I-8.95J0.0
G01 X-0.1
G00 Z10.
M5
G91 G28 Z0.0 M9
M01
T03 ( D12J )
( TOOL: D= 12. R= 0.0)
M6
T01
S2500 M3
X39.2 Y-34.2
Z1.
G01 Z-20.4 F175
X24.2 F350
X-20.2
X-27.9
G02 X-32.143 Y-32.443I0.0J6.
G01 X-32.443 Y-32.143
G02 X-34.2 Y-27.9I4.243J4.243
G01 Y27.9
G02 X-32.443 Y32.143I6.J0.0
G01 X-32.143 Y32.443
G02 X-27.9 Y34.2I4.243J-4.243
G01 X-20.2
X24.2
G02 X28.443 Y32.443I0.0J-6.
G01 X32.443 Y28.443
G02 X34.2 Y24.2I-4.243J-4.243
G01 Y-24.2
G02 X32.443 Y-28.443I-6.J0.0
G01 X28.443 Y-32.443
X17.836 Y-43.049
G00 Z10.
X4. Y0.0
Z1.
G01 Z-9. F105
X13.05 F350
G03I-13.05J0.0
G01 X4.
G00 Z10.
M5
G91 G28 Z0. M9
T1
M6
M30
%
楼主这是你给的后处理谢了~~能帮我在改哈嘛？

作者: fuxiaoyong1989 时间: 2009-8-1 14:17
%
O0999
G21
G91 G28 Z0.
G00 G17 G40 G49 G54 G80 G90
T01 ( D80R0.8 )
( TOOL: D= 80. R= 0.8)
M6
T10
G90G54G0X73.2Y0.0S1200M3
G43H01Z50.M8
Z1.
G01 Z0.0 F450
X28.2 F900
X-28.2
X-73.2
G00 Z10.
M5
G91 G28 Z0.0 M9
M01
T10 ( 20R0.8 )
( TOOL: D= 20. R= 0.8)
M6
T04
G90 G54 G0 X39.2 Y-38.3S2200 M3
G43H10Z50.M8
Z1.
G01 Z-21. F1100
X24.2 F2200
X-20.2
X-27.9
G02 X-35.042 Y-35.342I0.0J10.1
G01 X-35.342 Y-35.042
G02 X-38.3 Y-27.9I7.142J7.142
G01 Y27.9
G02 X-35.342 Y35.042I10.1J0.0
G01 X-35.042 Y35.342
G02 X-27.9 Y38.3I7.142J-7.142
G01 X-20.2
X24.2
G02 X31.342 Y35.342I0.0J-10.1
G01 X35.342 Y31.342
G02 X38.3 Y24.2I-7.142J-7.142
G01 Y-24.2
G02 X35.342 Y-31.342I-10.1J0.0
G01 X31.342 Y-35.342
X20.735 Y-45.948
G00 Z10.
M5
G91 G28 Z0.0 M9
M01
T04 ( ZD3 )
( TOOL: D= 10. R= 0.0)
M6
T05
G90G54G0X-23.55 Y-23.55 S1200M3
G43H04Z50.M8
G98 G81 X-23.55 Y-23.55 Z-1.8 R1. F80 M8
X23.55
X0.0 Y0.0
X-23.55 Y23.55
X23.55
G80 Z10.
M5
G91 G28 Z0.0 M9
M01
T05 ( Z22 )
( TOOL: D= 10. R= 0.0)
M6
T08
G90G54G0X0.0 Y0.0 S500 M3
G43H05Z50.M8
G98 G83 X0.0 Y0.0 Z-25. R1. Q3. F100 M8
G80 Z10.
M5
G91 G28 Z0.0 M9
M01
T08 ( Z3.3 )
( TOOL: D= 10. R= 0.0)
M6
T10
G90G54G0X-23.55 Y-23.55S1810 M3
G43H08Z50.M8
G98 G83 X-23.55 Y-23.55 Z-13.5 R1. Q2. F80 M8
X23.55
Y23.55
X-23.55
G80 Z10.
M5
G91 G28 Z0.0 M9
M01
T10 ( 20R0.8 )
( TOOL: D= 20. R= 0.8)
M6
T03
G90G54G0X-0.1 Y0.0 S2100 M3
G43H10Z50.M8
Z1.
G01 Z-11. F450
X8.95 F1500
G03I-8.95J0.0
G01 X-0.1
G00 Z10.
M5
G91 G28 Z0.0 M9
M01
T03 ( D12J )
( TOOL: D= 12. R= 0.0)
M6
T01
G90G54G0X39.2 Y-34.2S2500 M3
G43H03Z50.M8
Z1.
G01 Z-20.4 F175
X24.2 F350
X-20.2
X-27.9
G02 X-32.143 Y-32.443I0.0J6.
G01 X-32.443 Y-32.143
G02 X-34.2 Y-27.9I4.243J4.243
G01 Y27.9
G02 X-32.443 Y32.143I6.J0.0
G01 X-32.143 Y32.443
G02 X-27.9 Y34.2I4.243J-4.243
G01 X-20.2
X24.2
G02 X28.443 Y32.443I0.0J-6.
G01 X32.443 Y28.443
G02 X34.2 Y24.2I-4.243J-4.243
G01 Y-24.2
G02 X32.443 Y-28.443I-6.J0.0
G01 X28.443 Y-32.443
X17.836 Y-43.049
G00 Z10.
X4. Y0.0
Z1.
G01 Z-9. F105
X13.05 F350
G03I-13.05J0.0
G01 X4.
G00 Z10.
M5
G91 G28 Z0. M9
T1
M6
M30
%
像这样的楼主请看哈

作者: fuxiaoyong1989 时间: 2009-8-2 20:11
楼主你好~~~~~~~~~~~~~~~··

作者: fuxiaoyong1989 时间: 2009-8-2 20:12
麻烦你在帮我把后处理修改下，小弟先谢过了

作者: zbhouin 时间: 2009-8-2 21:05
要改干什么？一个是先到安全高度后定位，另一个是先定位后到安全高度。那只不过是你的习惯而已，不用改的

作者: fuxiaoyong1989 时间: 2009-8-3 23:42
你那上面只有一个刀补啊~~最好能帮我改到上面一样的，像你那样走的不安全呀，楼主在帮忙改下嘛~~，有修改cimit后处理教程吗给个，兄弟谢你了~~

作者: 289522140 时间: 2009-8-29 17:10
無語一下能用不就好了嗎

欢迎光临 iCAx开思网 (https://www.icax.org/)