<Mesh_Information>
<General_Information>
Mesh File Name = E:\moldflow\2102\Mesh\2101.mde
Mesh File Version = 2006
Total Element Number of Part = 428494
Total Node Number of Part = 428494
Total Element Number of Moldbase = 0
Total Node Number of Moldbase = 0
Total Element Number of Surface = 243462
Total Element Number = 281789
Total Node Number = 404974
</General_Information>
<Element_Type>
eDesign Meshing Level = 3
</Element_Type>
<Part_Mesh_Geometry>
Volume of Cavity = 187.852 cc
Volume of Cold Runner = 0 cc
Volume of Hot Runner = 0 cc
Total Volume = 187.852 cc
x-coordinate Range = (-8.58694, 7.72738) cm
y-coordinate Range = (-16.2947, 16.294) cm
y-coordinate Range = (0.0535382, 5.1533) cm
</Part_Mesh_Geometry>
<Moldbase_Geometry>
Volume of Moldbase = (32.6234 cm x 41 cm x 17.85 cm)
x-coordinate Range = (-16.5, 16.1234) cm
y-coordinate Range = (-20.5, 20.5) cm
z-coordinate Range = (-5.85, 12) cm
</Moldbase_Geometry>
</Mesh_Information>
==========================================================================
Moldex3D-Solid/Warp 9059.3
==========================================================================
==========================================================================
Moldex3D-Solid/Warp 9059.3
==========================================================================
<Computer_Information>
<General_Information>
Operating System = Microsoft Windows XP
Version = Professional Edition Service Pack 3 (Build 2600)
CPU = Intel(R) Pentium(R) Dual CPU E2200 @ 2.20GHz
</General_Information>
<Network_Information>
Description = Realtek RTL8168C(P)/8111C(P) PCI-E Gigabit Ethernet NIC
IP Address = 192.168.1.7
Subnet Mask = 255.255.255.0
Default Gateway = 192.168.1.1
MAC Address = 00-23-54-dd-09-ba
</Network_Information>
<Memory_Information>
Total Physical Memory = 2047 MB
Available Physical Memory = 1011 MB
</Memory_Information>
</Computer_Information>
==========================================================================
Moldex3D-Solid/Warp 9059.3
==========================================================================
<Run_Settings_Information>
Max. no. iteration = 50000
Convergence tolerance = 5.00e-005
Element type = Linear
Fiber orientation effect = OFF
Remove runner = ON
In-mold constraint effect = OFF
Moldbase deformation = OFF
Flow-induced residual stress effect = OFF
Solver acceleration = ON
</Run_Settings_Information>
==========================================================================
Moldex3D-Solid/Warp 9059.3
==========================================================================
---> Pure polymer: Analyse C2M stage, please wait...
XXX ERROR E5700 :
Symptom:
You may not have enough memory to run this case!
Solution:
Please try to increase your RAM or decrease total element number and rerun
the analysis again.作者: Micowen989 时间: 2009-4-26 10:12
Symptom:9 m: Z+ y% A8 {) g2 P
You may not have enough memory to run this case!! p! j) t7 D3 n" r
Solution:" [/ k7 P( i$ x* {# c$ A0 F
Please try to increase your RAM or decrease total element number and rerun
1 j9 N o+ g6 w% ]the analysis again.
说你没有足够的内存。作者: yuanfei 时间: 2009-4-26 11:59
可是我的内存已经2G了,难道还不够?作者: 493265073 时间: 2009-4-26 21:24 2G算什么。没有8G你别它理你。
用过此软件。只能这样评价它“烂软件一个”作者: yuanfei 时间: 2009-4-27 07:47
谢谢上面两位,看来是没有办法了.作者: lrbheyuan 时间: 2009-4-27 09:35
......
CAE的翹曲對內存要求都比較高,MF和MDX都是這樣作者: yuanfei 时间: 2009-4-27 09:55
不知道用这些软件需要怎样的配置.作者: lrbheyuan 时间: 2009-4-27 10:06
要看你的元素數量,還要看你使用什么材料,含纖維的材料對內存要求較高作者: lrbheyuan 时间: 2009-4-27 10:07
現在市面上的電腦基本都可以滿足了,內存最好大點,其他的沒有特殊要求