% / MFG0002
0 BEGIN PGM 71 MM
1 TOOL DEF 1 L+1,0000 R+0,5000
2 TOOL CALL 1 Z S200,000
3 L X+9,2200 Y-42,4940 Z+20,0000 R0 F10 M03
4 L X+9,2200 Y-42,4940 Z+4,0000 R0 F2000 M
5 L X+9,2200 Y-42,4940 Z+0,0000 R0 F2000 M03
6 L X+8,9810 Y-40,4340 Z-0,1570 R0 F M
7 L X+8,2760 Y-38,4840 Z-0,2120 R0 F M
8 L X+7,1440 Y-36,7460 Z-0,2490 R0 F M
9 L X+5,6450 Y-35,3130 Z-0,2730 R0 F M
10 L X+3,8570 Y-34,2620 Z-0,2890 R0 F M
11 L X+1,8760 Y-33,6480 Z-0,2980 R0 F M
12 L X+0,2190 Y-33,4940 Z-0,3000 R0 F M
13 L X-26,6090 Y-33,4980 Z-0,3000 R0 F M
14 L X-27,4730 Y-33,4610 Z-0,3000 R0 F M
15 L X-28,7860 Y-33,2800 Z-0,3000 R0 F M
16 L X-30,0770 Y-32,9570 Z-0,3000 R0 F M
17 L X-30,7440 Y-32,7240 Z-0,3000 R0 F M
18 L X-31,2170 Y-32,5360 Z-0,3000 R0 F M
19 L X-31,8230 Y-32,2560 Z-0,3000 R0 F M
20 L X-33,0070 Y-31,5820 Z-0,3000 R0 F M
21 L X-34,0850 Y-30,8020 Z-0,3000 R0 F M
22 L X-34,6280 Y-30,3240 Z-0,3000 R0 F M
23 L X-35,0000 Y-29,9740 Z-0,3000 R0 F M
24 L X-35,4980 Y-29,4440 Z-0,3000 R0 F M
25 L X-35,8230 Y-29,0510 Z-0,3000 R0 F M
26 L X-36,2670 Y-28,4750 Z-0,3000 R0 F M
27 L X-36,9730 Y-27,3560 Z-0,3000 R0 F M
28 L X-37,5730 Y-26,1290 Z-0,3000 R0 F M
29 L X-37,8150 Y-25,5020 Z-0,3000 R0 F M
30 L X-37,9730 Y-25,0160 Z-0,3000 R0 F M
31 L X-38,1600 Y-24,3480 Z-0,3000 R0 F M
32 L X-38,4010 Y-23,0360 Z-0,3000 R0 F M
33 L X-38,5060 Y-21,6100 Z-0,3000 R0 F M
34 L X-38,5130 Y+21,2540 Z-0,3000 R0 F M作者: sg0605 时间: 2007-5-30 13:37
后处理出来小数点变成逗号，圆弧都没有xyz，只有数字。作者: sg0605 时间: 2007-6-14 13:22
这个不能用啊。
不知道谁还有？
谢谢！作者: sxf20052005 时间: 2007-8-12 20:16
我有！要的话加我ＱＱ５７３３２５１４０我下次回厂里拷一个传给你！作者: mhx888 时间: 2010-9-19 02:04
我顶！！！！！作者: hezf300 时间: 2010-9-27 09:54
顶啊，这个后处理文件怎么没人上传作者: sdjsdj 时间: 2010-10-5 11:38
顶啊，这个后处理文件怎么没人上传作者: 風鈴夜雨 时间: 2011-11-16 00:11
谢谢了，下个回去试试作者: hhzooo 时间: 2014-5-28 17:23
学习学习作者: margar2016 时间: 2016-9-24 15:47
谢谢分享，感谢楼主