iCAx开思网
标题:
关于自动编程的，自己动手做,从其中提高自己
[打印本页]
作者:
夕阳挽照
时间:
2007-5-22 20:25
标题:
关于自动编程的，自己动手做,从其中提高自己
基本问题已解决，但还是很不足，自动光框和自动编骨位铜公的视频已上传，因为铜公类型错综复杂，所以先写了一个骨位铜公做试验。谢谢大家指点和提供宝贵的意见和建议.
[
本帖最后由 夕阳挽照 于 2007-5-24 21:29 编辑
]
作者:
夕阳挽照
时间:
2007-5-22 20:27
标题:
RT
实现了自动定义毛坯，从右键里实现自动编程，每天工作太忙，所以，做得很仓促，想求助高手出招，发些有类型的图，和有说服力的刀路做参考，以便大家提高，做成适合自己的自动电极编程。
[
本帖最后由 夕阳挽照 于 2007-5-24 21:32 编辑
]
作者:
夕阳挽照
时间:
2007-5-22 20:29
标题:
RT
RT
[
本帖最后由 夕阳挽照 于 2007-5-24 21:33 编辑
]
作者:
夕阳挽照
时间:
2007-5-22 21:39
标题:
把帖子顶起来。为大家做贡献，请高手指点。
把帖子顶起来。为大家做贡献，请高手指点。
IMPORT TEMPLATE ENTITY TOOLPATH "Favourites\Offset-AreaClear-Model.ptf" FORM TOOLPATH
CREATE TOOL '30R5' tipradiused EDIT TOOL '30R5' DIAMETER 30 EDIT TOOL '30R5' TIPRADIUS 5 EDIT TOOL '30R5' FEED_RATE_REC 3000 EDIT TOOL '30R5' SPINDLE_SPEED_REC 1800 FEEDRATE ACCEPT
EDIT LMOVES RAMP
EDIT RTOLERANCE 0.02
FORM THICKNESS EDIT THICKNESS TAB GENERAL
EDIT RTHICKNESS AXIAL_RADIAL ON
EDIT RTHICKNESS 0.35
EDIT RTHICKNESS AXIAL 0.1
THICKNESS ACCEPT
EDIT OVER 5
EDIT ZHEIGHTS AUTOMATIC STEPDOWN .4
EDIT LINKS STRAIGHT
EDIT OFFSETDIRECTION OUTSIDEIN
EDIT ACUTDIR CLIMB
EDIT AREAFILTERVALUE 0.5
EDIT TOOLPATH "1" CALCULATE
RENAME Toolpath "1" "01"
AREACLEAR CANCEL
FORM LEADLINK
EDIT TOOLPATH LEADS SKIMDIST 5
EDIT TOOLPATH LEADS PLUNGEDIST 0.3
EDIT TOOLPATH LEADS INCREMENT_FROM_STOCK N
EDIT TOOLPATH LEADS PAGE LEADIN
EDIT TOOLPATH LEADS LEADIN RAMP
FORM PMLLEADINRAMP
EDIT TOOLPATH LEADS LEADIN RAMPOPT HEIGHT_INCREMENT .7
EDIT TOOLPATH LEADS LEADIN RAMPOPT ZIGANGLE 2
LEADINRAMP ACCEPT
EDIT TOOLPATH LEADS PAGE LINK
EDIT TOOLPATH LEADS LINK INCR
EDIT TOOLPATH LEADS LONGLINK INCR
PROCESS TPLEADS
LEADS ACCEPT
IMPORT TEMPLATE ENTITY TOOLPATH "Favourites\Constant-Z-Finishing.ptf" FORM TOOLPATH
CREATE TOOL '17R0.8' tipradiused EDIT TOOL '17R0.8' DIAMETER 17 EDIT TOOL '17R0.8' TIPRADIUS 0.8 EDIT TOOL '17R0.8' FEED_RATE_REC 2000 EDIT TOOL '17R0.8' SPINDLE_SPEED_REC 2000 FEEDRATE ACCEPT
EDIT CONSTZ SPIRAL ON
EDIT FTOLERANCE "0.01"
EDIT STEPDOWN 0.2
FORM THICKNESS EDIT THICKNESS TAB GENERAL
EDIT FTHICKNESS AXIAL_RADIAL ON
EDIT FTHICKNESS 0.15
EDIT FTHICKNESS AXIAL 0.1
THICKNESS APPLY
THICKNESS ACCEPT
EDIT TOOLPATH "1" CALCULATE
RENAME Toolpath "1" "02"
EDIT TOOLPATH "02" REAPPLYFROMGUI
FINISHING CANCEL
FORM FEEDRATE
EDIT PRATE 2000
EDIT COOLANT FLOOD
EDIT DATAFROMTOOL ;
RESET TOOLPATH FEEDRATE
FEEDRATE ACCEPT
FORM LEADLINK
FORM LEADLINK
EDIT TOOLPATH LEADS PAGE ZHEIGHTS
EDIT TOOLPATH LEADS SKIMDIST 5
EDIT TOOLPATH LEADS PLUNGEDIST 0.3
EDIT TOOLPATH LEADS INCREMENT_FROM_STOCK N
EDIT TOOLPATH LEADS PAGE LEADIN
EDIT TOOLPATH LEADS LEADIN RAMP
FORM PMLLEADINRAMP
EDIT TOOLPATH LEADS LEADIN RAMPOPT HEIGHT_INCREMENT 0.3
EDIT TOOLPATH LEADS LEADIN RAMPOPT ZIGANGLE 2
LEADINRAMP ACCEPT
EDIT TOOLPATH LEADS PAGE LINK
EDIT TOOLPATH LEADS LINK INCR
EDIT TOOLPATH LEADS LONGLINK INCR
PROCESS TPLEADS
LEADS ACCEPT
ACTIVATE TOOL "17R0.8"
IMPORT TEMPLATE ENTITY TOOLPATH "Favourites\Constant-Z-Finishing.ptf" FORM TOOLPATH
EDIT CONSTZ SPIRAL ON
EDIT FTOLERANCE "0.01"
EDIT STEPDOWN 0.15
FORM THICKNESS EDIT THICKNESS TAB GENERAL
EDIT FTHICKNESS AXIAL_RADIAL ON
EDIT FTHICKNESS 0
EDIT FTHICKNESS AXIAL 0
THICKNESS APPLY
THICKNESS ACCEPT
EDIT TOOLPATH "1" CALCULATE
RENAME Toolpath "1" "03"
EDIT TOOLPATH "03" REAPPLYFROMGUI
FINISHING CANCEL
FORM FEEDRATE
EDIT PRATE 2000
EDIT COOLANT FLOOD
EDIT DATAFROMTOOL ;
RESET TOOLPATH FEEDRATE
FEEDRATE ACCEPT
FORM LEADLINK
FORM LEADLINK
EDIT TOOLPATH LEADS PAGE ZHEIGHTS
EDIT TOOLPATH LEADS SKIMDIST 5
EDIT TOOLPATH LEADS PLUNGEDIST 0.3
EDIT TOOLPATH LEADS INCREMENT_FROM_STOCK N
EDIT TOOLPATH LEADS PAGE LEADIN
EDIT TOOLPATH LEADS LEADIN RAMP
FORM PMLLEADINRAMP
EDIT TOOLPATH LEADS LEADIN RAMPOPT HEIGHT_INCREMENT 0.3
EDIT TOOLPATH LEADS LEADIN RAMPOPT ZIGANGLE 2
LEADINRAMP ACCEPT
EDIT TOOLPATH LEADS PAGE LINK
EDIT TOOLPATH LEADS LINK INCR
EDIT TOOLPATH LEADS LONGLINK INCR
PROCESS TPLEADS
LEADS ACCEPT
ACTIVATE TOOL "17R0.8"
FORM BLOCK
EDIT BLOCK YMIN LOCK
EDIT BLOCK XMIN LOCK
EDIT BLOCK XMAX LOCK
EDIT BLOCK YMAX LOCK
EDIT BLOCK ZMIN LOCK
EDIT BLOCK ZMAX UNLOCK
EDIT BLOCK RESETLIMIT -.1
EDIT BLOCK RESET
EDIT BLOCK ALL UNLOCK
BLOCK ACCEPT
IMPORT TEMPLATE ENTITY TOOLPATH "Favourites\Offset-AreaClear-Model.ptf" FORM TOOLPATH
SET AREACLEAREXPERT
EDIT AREACLEAR TYPE FLAT
EDIT RTOLERANCE 0.01
EDIT LMOVES RAMP
FORM THICKNESS EDIT THICKNESS TAB GENERAL
EDIT RTHICKNESS AXIAL_RADIAL ON
EDIT RTHICKNESS 0.4
EDIT RTHICKNESS AXIAL 0
EDIT FTHICKNESS AXIAL_RADIAL OFF
THICKNESS APPLY
THICKNESS ACCEPT
EDIT OVER 10
EDIT AREAFILTER ON
EDIT AREAFILTERVALUE 1.5
EDIT TOOLPATH "1" CALCULATE
RENAME Toolpath "1" "04"
EDIT TOOLPATH "04" REAPPLYFROMGUI
AREACLEAR CANCEL
FORM FEEDRATE
EDIT COOLANT FLOOD
EDIT DATAFROMTOOL ;
RESET TOOLPATH FEEDRATE
FEEDRATE ACCEPT
FORM LEADLINK
EDIT TOOLPATH LEADS SKIMDIST 5
EDIT TOOLPATH LEADS PLUNGEDIST 0.3
EDIT TOOLPATH LEADS INCREMENT_FROM_STOCK N
EDIT TOOLPATH LEADS PAGE LEADIN
EDIT TOOLPATH LEADS LEADIN RAMP
FORM PMLLEADINRAMP
EDIT TOOLPATH LEADS LEADIN RAMPOPT ZIGANGLE 2
EDIT TOOLPATH LEADS LEADIN RAMPOPT HEIGHT_INCREMENT 0.3
LEADINRAMP ACCEPT
EDIT TOOLPATH LEADS PAGE LINK
EDIT TOOLPATH LEADS LINK INCR
EDIT TOOLPATH LEADS LONGLINK INCR
PROCESS TPLEADS
LEADS ACCEPT
作者:
夕阳挽照
时间:
2007-5-22 21:44
标题:
把帖子顶起来。为大家做贡献，请高手指点。
把帖子顶起来。为大家做贡献，请高手指点。
IMPORT TEMPLATE ENTITY TOOLPATH "Favourites\Offset-AreaClear-Model.ptf" FORM TOOLPATH
CREATE TOOL '30R5' tipradiused EDIT TOOL '30R5' DIAMETER 30 EDIT TOOL '30R5' TIPRADIUS 5 EDIT TOOL '30R5' FEED_RATE_REC 3000 EDIT TOOL '30R5' SPINDLE_SPEED_REC 1800 FEEDRATE ACCEPT
EDIT LMOVES RAMP
EDIT RTOLERANCE 0.02
FORM THICKNESS EDIT THICKNESS TAB GENERAL
EDIT RTHICKNESS AXIAL_RADIAL ON
EDIT RTHICKNESS 0.35
EDIT RTHICKNESS AXIAL 0.1
THICKNESS ACCEPT
EDIT OVER 5
EDIT ZHEIGHTS AUTOMATIC STEPDOWN .4
EDIT LINKS STRAIGHT
EDIT OFFSETDIRECTION OUTSIDEIN
EDIT ACUTDIR CLIMB
EDIT AREAFILTERVALUE 0.5
EDIT TOOLPATH "1" CALCULATE
RENAME Toolpath "1" "01"
AREACLEAR CANCEL
FORM LEADLINK
EDIT TOOLPATH LEADS SKIMDIST 5
EDIT TOOLPATH LEADS PLUNGEDIST 0.3
EDIT TOOLPATH LEADS INCREMENT_FROM_STOCK N
EDIT TOOLPATH LEADS PAGE LEADIN
EDIT TOOLPATH LEADS LEADIN RAMP
FORM PMLLEADINRAMP
EDIT TOOLPATH LEADS LEADIN RAMPOPT HEIGHT_INCREMENT .7
EDIT TOOLPATH LEADS LEADIN RAMPOPT ZIGANGLE 2
LEADINRAMP ACCEPT
EDIT TOOLPATH LEADS PAGE LINK
EDIT TOOLPATH LEADS LINK INCR
EDIT TOOLPATH LEADS LONGLINK INCR
PROCESS TPLEADS
LEADS ACCEPT
IMPORT TEMPLATE ENTITY TOOLPATH "Favourites\Constant-Z-Finishing.ptf" FORM TOOLPATH
CREATE TOOL '17R0.8' tipradiused EDIT TOOL '17R0.8' DIAMETER 17 EDIT TOOL '17R0.8' TIPRADIUS 0.8 EDIT TOOL '17R0.8' FEED_RATE_REC 2000 EDIT TOOL '17R0.8' SPINDLE_SPEED_REC 2000 FEEDRATE ACCEPT
EDIT CONSTZ SPIRAL ON
EDIT FTOLERANCE "0.01"
EDIT STEPDOWN 0.2
FORM THICKNESS EDIT THICKNESS TAB GENERAL
EDIT FTHICKNESS AXIAL_RADIAL ON
EDIT FTHICKNESS 0.15
EDIT FTHICKNESS AXIAL 0.1
THICKNESS APPLY
THICKNESS ACCEPT
EDIT TOOLPATH "1" CALCULATE
RENAME Toolpath "1" "02"
EDIT TOOLPATH "02" REAPPLYFROMGUI
FINISHING CANCEL
FORM FEEDRATE
EDIT PRATE 2000
EDIT COOLANT FLOOD
EDIT DATAFROMTOOL ;
RESET TOOLPATH FEEDRATE
FEEDRATE ACCEPT
FORM LEADLINK
FORM LEADLINK
EDIT TOOLPATH LEADS PAGE ZHEIGHTS
EDIT TOOLPATH LEADS SKIMDIST 5
EDIT TOOLPATH LEADS PLUNGEDIST 0.3
EDIT TOOLPATH LEADS INCREMENT_FROM_STOCK N
EDIT TOOLPATH LEADS PAGE LEADIN
EDIT TOOLPATH LEADS LEADIN RAMP
FORM PMLLEADINRAMP
EDIT TOOLPATH LEADS LEADIN RAMPOPT HEIGHT_INCREMENT 0.3
EDIT TOOLPATH LEADS LEADIN RAMPOPT ZIGANGLE 2
LEADINRAMP ACCEPT
EDIT TOOLPATH LEADS PAGE LINK
EDIT TOOLPATH LEADS LINK INCR
EDIT TOOLPATH LEADS LONGLINK INCR
PROCESS TPLEADS
LEADS ACCEPT
ACTIVATE TOOL "17R0.8"
IMPORT TEMPLATE ENTITY TOOLPATH "Favourites\Constant-Z-Finishing.ptf" FORM TOOLPATH
EDIT CONSTZ SPIRAL ON
EDIT FTOLERANCE "0.01"
EDIT STEPDOWN 0.15
FORM THICKNESS EDIT THICKNESS TAB GENERAL
EDIT FTHICKNESS AXIAL_RADIAL ON
EDIT FTHICKNESS 0
EDIT FTHICKNESS AXIAL 0
THICKNESS APPLY
THICKNESS ACCEPT
EDIT TOOLPATH "1" CALCULATE
RENAME Toolpath "1" "03"
EDIT TOOLPATH "03" REAPPLYFROMGUI
FINISHING CANCEL
FORM FEEDRATE
EDIT PRATE 2000
EDIT COOLANT FLOOD
EDIT DATAFROMTOOL ;
RESET TOOLPATH FEEDRATE
FEEDRATE ACCEPT
FORM LEADLINK
FORM LEADLINK
EDIT TOOLPATH LEADS PAGE ZHEIGHTS
EDIT TOOLPATH LEADS SKIMDIST 5
EDIT TOOLPATH LEADS PLUNGEDIST 0.3
EDIT TOOLPATH LEADS INCREMENT_FROM_STOCK N
EDIT TOOLPATH LEADS PAGE LEADIN
EDIT TOOLPATH LEADS LEADIN RAMP
FORM PMLLEADINRAMP
EDIT TOOLPATH LEADS LEADIN RAMPOPT HEIGHT_INCREMENT 0.3
EDIT TOOLPATH LEADS LEADIN RAMPOPT ZIGANGLE 2
LEADINRAMP ACCEPT
EDIT TOOLPATH LEADS PAGE LINK
EDIT TOOLPATH LEADS LINK INCR
EDIT TOOLPATH LEADS LONGLINK INCR
PROCESS TPLEADS
LEADS ACCEPT
ACTIVATE TOOL "17R0.8"
FORM BLOCK
EDIT BLOCK YMIN LOCK
EDIT BLOCK XMIN LOCK
EDIT BLOCK XMAX LOCK
EDIT BLOCK YMAX LOCK
EDIT BLOCK ZMIN LOCK
EDIT BLOCK ZMAX UNLOCK
EDIT BLOCK RESETLIMIT -.1
EDIT BLOCK RESET
EDIT BLOCK ALL UNLOCK
BLOCK ACCEPT
IMPORT TEMPLATE ENTITY TOOLPATH "Favourites\Offset-AreaClear-Model.ptf" FORM TOOLPATH
SET AREACLEAREXPERT
EDIT AREACLEAR TYPE FLAT
EDIT RTOLERANCE 0.01
EDIT LMOVES RAMP
FORM THICKNESS EDIT THICKNESS TAB GENERAL
EDIT RTHICKNESS AXIAL_RADIAL ON
EDIT RTHICKNESS 0.4
EDIT RTHICKNESS AXIAL 0
EDIT FTHICKNESS AXIAL_RADIAL OFF
THICKNESS APPLY
THICKNESS ACCEPT
EDIT OVER 10
EDIT AREAFILTER ON
EDIT AREAFILTERVALUE 1.5
EDIT TOOLPATH "1" CALCULATE
RENAME Toolpath "1" "04"
EDIT TOOLPATH "04" REAPPLYFROMGUI
AREACLEAR CANCEL
FORM FEEDRATE
EDIT COOLANT FLOOD
EDIT DATAFROMTOOL ;
RESET TOOLPATH FEEDRATE
FEEDRATE ACCEPT
FORM LEADLINK
EDIT TOOLPATH LEADS SKIMDIST 5
EDIT TOOLPATH LEADS PLUNGEDIST 0.3
EDIT TOOLPATH LEADS INCREMENT_FROM_STOCK N
EDIT TOOLPATH LEADS PAGE LEADIN
EDIT TOOLPATH LEADS LEADIN RAMP
FORM PMLLEADINRAMP
EDIT TOOLPATH LEADS LEADIN RAMPOPT ZIGANGLE 2
EDIT TOOLPATH LEADS LEADIN RAMPOPT HEIGHT_INCREMENT 0.3
LEADINRAMP ACCEPT
EDIT TOOLPATH LEADS PAGE LINK
EDIT TOOLPATH LEADS LINK INCR
EDIT TOOLPATH LEADS LONGLINK INCR
PROCESS TPLEADS
LEADS ACCEPT
作者:
hao2008888
时间:
2007-5-22 21:49
好贴!
高手请出招,小弟也想学.
一起顶.........
作者:
dq126-lisanmei
时间:
2007-5-23 06:47
我不知道你们是怎样做的,我都可以做到简单铜公的自动编程的,但是我不会发上来,有谁指点一下,
作者:
夕阳挽照
时间:
2007-5-23 08:25
标题:
RT
楼上的。你能用一个宏就能写完一个铜公还是写一条程式啊，如只是写一条程式，那达不到要求。
作者:
夕阳挽照
时间:
2007-5-23 14:43
顶起来。大家提点意见。走过路过发表一下自己的想法。
作者:
夕阳挽照
时间:
2007-5-23 16:41
顶起来。大家提点意见。走过路过发表一下自己的想法。
作者:
夕阳挽照
时间:
2007-5-24 19:22
标题:
PM就这么沉没吗。这个思路大家都舍不得讨论下？
问题已解决，还是自己动手好。本来想起个抛砖引玉的作用，没想到大家对自动编程没兴趣，自己做的虽然没有买的那么完美（也许），但是在做的过程中，大家都可以积累很多经验，做成功之后，可以解决一部份类型的加工，而且不用自己去烦，等下我发个视频的上来。，自动开框，自动铜公编程（部分简单类型）。现本人正在尽力完善，不足之处请大家指点。
作者:
夕阳挽照
时间:
2007-5-24 20:03
标题:
先来个21R0.8飞刀光框的自动编程。
1、2
作者:
夕阳挽照
时间:
2007-5-24 20:07
3-4
作者:
sfy3344
时间:
2007-5-24 20:13
有很大兴趣
作者:
夕阳挽照
时间:
2007-5-24 20:20
5-6
作者:
夕阳挽照
时间:
2007-5-24 20:51
现在发个精雕光骨位类型的铜公，光刀用最佳4MM等高，开粗用8MM，希望听点大家的意见，便于改进，谢谢。
作者:
夕阳挽照
时间:
2007-5-24 20:56
3-4
作者:
夕阳挽照
时间:
2007-5-24 20:58
5-6
作者:
夕阳挽照
时间:
2007-5-24 21:01
7-8-9-10-11-12-13-14
作者:
夕阳挽照
时间:
2007-5-24 21:09
15-21
作者:
夕阳挽照
时间:
2007-5-24 21:19
17-18
作者:
夕阳挽照
时间:
2007-5-24 21:19
今天上传不了，明在继续，希望高手出招，小弟借地献丑了。只能提供思路，等高手来指点。
作者:
lovespring006
时间:
2007-5-25 14:44
用宏来做还叫自动啊，那好比小孩子背唐诗，很死板的，有空研究一下VB了
作者:
xiaofeng2046
时间:
2007-5-25 17:40
用宏可做简单电极
作者:
kugo
时间:
2007-5-28 13:16
顶一下，期待楼主继续精彩的讲解！
想学的兄弟也跟着顶呀，要不，人家哪有＂精力＂再讲呀！
作者:
peterxieai
时间:
2007-5-28 14:14
编的程还没有上过机,不知什么时候有机会自已写个自动的编的程序
作者:
972258
时间:
2007-5-28 21:13
宏编的上机可以用,不过我建议还是多检查几遍,即使我现在所使用的是正版的软件,有时后也会出现的问题!
作者:
mjtppf
时间:
2007-7-3 11:07
宏命令，不错的，对同一类型的模型，可以在做第一个时录制宏，后面的就可以直接运行这个录制好的宏了，很方便；
但不管有多么“自动”，必要的编辑都是不可少的，“自动”编程做得再好，也不能涵盖所以的可能性，人还是要发挥很大作用的；
刀具路径计算是一回事，计算完成后能不能够方便地编辑是另一回事，有时编辑甚至比计算更重要，因为CAM软件路径计算的思路和算法是很类似的，仔细分析，常见的就是那几种，而方便地编辑对一款优秀的CAM软件是至关重要的，有时甚至成为人们选择软件的决定因素。
以上是我的个人看法，请大家各抒己见，再顶楼主。
[
本帖最后由 mjtppf 于 2007-7-3 11:18 编辑
]
作者:
hf000
时间:
2007-7-18 16:55
还有呢?为什么不传啊?
作者:
ymytxb
时间:
2007-7-20 20:39
期待楼主上传,楼主讲得很精彩.
作者:
ymytxb
时间:
2007-7-25 20:15
楼 主怎么一点都不负责了,好端端的传了前一部分.后一部分就不管了.害得我天天都在盼.
作者:
wukenwen
时间:
2007-7-27 18:56
好啊
作者:
yin2847
时间:
2007-11-16 13:11
楼主剩下的文件怎么忘传了，，
我也对自动编程很感兴趣，平常也全都是用宏在做，效率很高，
PM的宏简直是太赞了，用好她编程太轻松了，
PM的宏使PM立于不败之地，
作者:
夕阳挽照
时间:
2007-11-16 20:11
对不起大家。我好久没上网了。其实我天天在。只不过。由于搬厂原因，放了很久的假，跑去玩游戏去了。我重新开了个新贴子，希望喜欢的朋友，去跟贴，你的意见，有我们需要的。
作者:
Zzz129
时间:
2007-11-30 19:35
有空加我吧QQ627478835
作者:
powerpc1
时间:
2008-3-18 23:58
细心蜻蜓啊！！
作者:
cnc2046
时间:
2008-3-19 20:12
还不会自动编程!
[
本帖最后由 cnc2046 于 2008-3-19 20:13 编辑
]
作者:
dazhi888
时间:
2008-10-18 16:34
标题:
请教，
下载了，可是解压不了啊
作者:
chenqinliqin
时间:
2009-8-2 10:09
期待楼主上传一些具体做自动编程宏的方法技巧！~~~~~~~~~不胜感激！~~~~~~
欢迎光临 iCAx开思网 (https://www.icax.org/)
Powered by Discuz! X3.3
