iCAx开思网

标题: 西门子机子的传输程式 [打印本页]

作者: 风之涯 时间: 2007-3-26 20:58
标题: 西门子机子的传输程式
Sample Text请教各位一个问题，我公司机床是西门子控制系统（老式820的），自带的传输软件不能在WINXP里传出程式，只能丛机床传到电脑里（说明参数设置没有问题），另外从98系统就能正常传输，不知道是什么原因，请高手指点一二！！

作者: 风之涯 时间: 2007-3-28 21:02
有的同志请帮帮小弟一下咯，98、XP两边捣，累死人啊5555

作者: changan001 时间: 2007-4-2 04:04
98里面是不是能传能收？能说详细点吗？

作者: 风之涯 时间: 2007-4-2 11:53
就是啊，98。ME里都可以，就是到XP里不行，不知道为什么，有时只能传进程式的开头部分，机床就报警，请大大们帮帮我！！

作者: 风之涯 时间: 2007-4-2 12:03
就是啊，98。ME里都可以，就是到XP里不行，不知道为什么，有时只能传进程式的开头部分，机床就报警，请大大们帮帮我！！

作者: 风之涯 时间: 2007-4-3 20:49
总算找到一个，可以在XP下用，好爽！
大家分享一下，不过找不到它的配置文件，知道的朋友，请指点一下！！

作者: 风之涯 时间: 2007-4-3 20:51
界面如下

作者: liangantong 时间: 2007-4-7 22:58
风兄,你好!
我的PROE\NC程式输入过数电脑后,启动机床,啥反应也没有,
是不是传输软件的问题?系统也是西门子的,(电脑系统WIN98) ,能否给个传输软件试一下?
另外,你用啥后处理?也给一个来怎样?

会用PROE\NC一个多月了,就是不能实践,郁闷啊！！！

[ 本帖最后由 liangantong 于 2007-4-8 05:57 编辑 ]

作者: 风之涯 时间: 2007-4-8 20:48

原帖由 liangantong 于 2007-4-7 22:58 发表
风兄,你好!
我的PROE\NC程式输入过数电脑后,启动机床,啥反应也没有,
是不是传输软件的问题?系统也是西门子的,(电脑系统WIN98) ,能否给个传输软件试一下?
另外,你用啥后处理?也给一个来怎样?

会用PROE\NC一个 ...

你的是西门子哪个系列的，820还是840，还是802的，程式单出一个，我来试试改一个，（我也不太会），传输软件里要做一些设置，其参数要和你的机床参数一致才行，如果在98系统的话就不要用这个软件，西门子自已的就好用的多了，我发的这个要不得不在XP下传输才用的，——————

作者: liangantong 时间: 2007-4-9 07:36
风兄:谢谢你的回复!我好像抓住了一根救命稻草．
我厂电脑锣所用系统:SINUMERIK 802 S BASE LINE,应该就是你所提到的802吧?
以下311.NC(第一个,12.1kb，部分删除)为MC编出来能正常运作的程式,P311(第二个,1.36kb)为PROE编出,机床无反应的程式,两个程式均为同一零件的外围铣削,但程式的大小怎么相差那么远?
再次感谢!!
%_N_311_MPF
;$PATH=/_N_MPF_DIR
G54 G00
G90 G64
S2500M3
G00X-29.09Y-35.585M08
Z10.
Z-1.857
G1Z-2.857F600.
G3X-28.536Y-28.536I-3.247J3.802F2000.
G1X-29.045Y-27.939
X-29.455Y-27.27
X-29.755Y-26.545
X-29.938Y-25.782
X-30.Y-25.
Y24.761
Y25.
X-29.949Y25.712
X-29.941Y25.748
X-29.938Y25.782
X-29.888Y25.99
X-29.797Y26.409
X-29.771Y26.48
X-29.755Y26.545
X-29.668Y26.756
X-29.548Y27.077
X-29.493Y27.177
X-29.455Y27.27
X-29.343Y27.453
X-29.206Y27.703
X-29.114Y27.826
X-29.045Y27.939
755
X-26.48Y29.771
X-26.409Y29.797
X-25.99Y29.888
X-25.782Y29.938
XX-27.939Y-29.045
X-28.536Y-28.536
G3X-35.585Y-29.09I-3.247J-3.802
G1X-29.09Y-35.585
Z-5.714F600.
G3X-28.536Y-28.536I-3.247J3.802F2000.
G1X-29.045Y-27.939
X-29.455Y-27.27
X-29.755Y-26.545
X-29.938Y-25.782
X-30.Y-25.
Y24.408
Y25.001
X-29.999Y25.01
X
X-28.084Y28.921
X-27.939Y29.045

X-25.748Y29.941
X-25.712Y29.949
X-25.Y30.
X24.408
X25.001
X25.782Y29.938
X26.545Y29.755
Y-25.
X29.998Y-25.03
X29.949Y-25.712
X29.941Y-25.748
X29.938Y-25.782
X29.888Y-25.99
X29.797Y-26.409
X29.771Y-26.48
X29.755Y-26.545
X29.668Y-26.756
X29.548Y-27.077
X29.493Y-27.177
X29.455Y-27.27
X29.343Y-27.453
X29.206Y-27.703
X29.114Y-27.826
X29.045Y-27.939
X28.921Y-28.084
X28.779Y-28.274
X28.641Y-28.412
X28.536Y-28.536
X28.412Y-28.641
X28.274Y-28.779
X28.084Y-28.921
X27.939Y-29.045
X27.826Y-29.114
X27.703Y-29.206
X27.453Y-29.343
X27.27Y-29.455
X27.177Y-29.493
X27.077Y-29.548
X26.756Y-29.668
X26.545Y-29.755
X26.48Y-29.771
X26.409Y-29.797
X25.99Y-29.888
X25.782Y-29.938
X25.748Y-29.941
X25.712Y-29.949
X25.002Y-30.
X25.
X-25.
X-25.782Y-29.938
X-26.545Y-29.755
X-27.27Y-29.455
X-27.939Y-29.045
X-28.536Y-28.536
G3X-35.585Y-29.09I-3.247J-3.802
G1X-29.09Y-35.585
Z-8.571F600.
G3X-28.536Y-28.536I-3.247J3.802F2000.
G1X-29.045Y-27.939
X-29.455Y-27.27
X-29.755Y-26.545
X-29.938Y-25.782
X-30.Y-25.
Y25.001
X-29.949Y25.712
X-29.941Y25.748
X-29.938Y25.782
X-29.888Y25.99
X-29.797Y26.409
X-29.771Y26.48
X-29.755Y26.545
X-29.668Y26.756
X-29.548Y27.077
X-29.493Y27.177
X-29.455Y27.27
X-29.343Y27.453
X-29.206Y27.703
X-29.114Y27.826
X-29.045Y27.939
X-28.921Y28.084
X-28.779Y28.274
X-28.641Y28.412
X-28.536Y28.536
X-28.412Y28.641
X-28.274Y28.779
X-28.084Y28.921
X-27.939Y29.045
X-27.826Y29.114
X-27.703Y29.206
X-27.453Y29.343
X-27.27Y29.455
X-27.177Y29.493
X-27.077Y29.548
X-26.756Y29.668
X-26.545Y29.755
X-26.48Y29.771
X-26.409Y29.797
X-25.99Y29.888
X-25.782Y29.938
X-25.748Y29.941
X-25.712Y29.949
X-25.Y30.
X25.001
X25.782Y29.938
X26.545Y29.755
X27.27Y29.455
X27.939Y29.045
X28.536Y28.536
X29.045Y27.939
X29.455Y27.27
X29.755Y26.545
X29.938Y25.782
X30.Y25.
Y-25.
X29.998Y-25.03
X29.949Y-25.712
X29.941Y-25.748
X29.938Y-25.782
X29.888Y-25.99
X29.797Y-26.409
X29.771Y-26.48
X28.274Y-28.779
X28.084Y-28.921
X27.939Y-29.045
X27.826Y-29.114
X27.703Y-29.206
X27.453Y-29.343
X27.27Y-29.455
X27.177Y-29.493
X27.077Y-29.548
X26.756Y-29.668
X25.712Y-29.949
X25.002Y-30.
X25.
X-25.
X-25.782Y-29.938
X-26.545Y-29.755
X-27.27Y-29.455
X-27.939Y-29.045
X-28.536Y-28.536
G3X-35.585Y-29.09I-3.247J-3.802
G1X-29.09Y-35.585
Z-11.429F600.
G3X-28.536Y-28.536I-3.247J3.802F2000.
G1X-29.045Y-27.939
X-29.455Y-27.27
X-29.755Y-26.545
X-29.938Y-25.782
X-30.Y-25.
Y25.001
X-29.949Y25.712
X-29.941Y25.748
X-29.938Y25.782
X-29.888Y25.99
X-29.797Y26.409
X-29.771Y26.48
X-29.755Y26.545
X-29.668Y26.756
X-29.548Y27.077
X-29.493Y27.177
X-29.455Y27.27
X-29.343Y27.453
X-29.206Y27.703
X-29.114Y27.826
X-29.045Y27.939
X-28.921Y28.084
X-28.779Y28.274
X-28.641Y28.412
X-28.536Y28.536
X-28.412Y28.641
X-28.274Y28.779
X-28.084Y28.921
X-27.939Y29.045
X-27.826Y29.114
X-27.703Y29.206
X-27.453Y29.343
X-27.27Y29.455
X-27.177Y29.493
X-27.077Y29.548
X-26.756Y29.668
X-26.545Y29.755
X-26.48Y29.771
X-26.409Y29.797
X-25.99Y29.888
X-25.782Y29.938
X-25.748Y29.941
X-25.712Y29.949
X-25.Y30.
X25.001
X30.Y25.
Y-25.
X29.998Y-25.03
X29.949Y-25.712
X29.941Y-25.748
X29.938Y-25.782
X29.888Y-25.99
X29.797Y-26.409
X29.771Y-26.48
X29.755Y-26.545
X29.668Y-26.756
X29.548Y-27.077
X29.493Y-27.177
X29.455Y-27.27
X29.343Y-27.453
X29.206Y-27.703
X29.114Y-27.826
X29.045Y-27.939
X28.921Y-28.084
X28.779Y-28.274
X28.641Y-28.412
X28.536Y-28.536
X28.412Y-28.641
X28.274Y-28.779
X28.084Y-28.921
X27.939Y-29.045
X27.826Y-29.114
X27.703Y-29.206
X27.453Y-29.343
X27.27Y-29.455
X27.177Y-29.493
X27.077Y-29.548
X26.756Y-29.668
X26.545Y-29.755
X26.48Y-29.771
X26.409Y-29.797
X25.99Y-29.888
X25.782Y-29.938
X25.748Y-29.941
X25.712Y-29.949
X25.002Y-30.
X25.
X-25.
X-25.782Y-29.938
X-26.545Y-29.755
X-27.27Y-29.455
X-27.939Y-29.045
X-28.536Y-28.536
G3X-35.585Y-29.09I-3.247J-3.802
G1X-29.09Y-35.585
Z-14.286F600.
G3X-28.536Y-28.536I-3.247J3.802F2000.
G1X-29.045Y-27.939
X-29.455Y-27.27
X-29.755Y-26.545
X-29.938Y-25.782
X-30.Y-25.
Y25.001
X-29.949Y25.712
X-29.941Y25.748
X-29.938Y25.782
X-29.888Y25.99
X-29.797Y26.409
X-29.771Y26.48
X-29.755Y26.545
X-29.668Y26.756
X-29.548Y27.077
X-29.493Y27.177
X-29.455Y27.27
X-29.343Y27.453
X-29.206Y27.703
X-29.114Y27.826
X-29.045Y27.939
X-28.921Y28.084
X-28.779Y28.274
X-28.641Y28.412
X-28.536Y28.536
X-28.412Y28.641
X-28.274Y28.779
X-28.084Y28.921
X-27.939Y29.045
X-27.826Y29.114
X-27.703Y29.206
X-27.453Y29.343
X-27.27Y29.455
X-27.177Y29.493
X-27.077Y29.548
X-26.756Y29.668
X-26.545Y29.755
X-26.48Y29.771
X-26.409Y29.797
X-25.99Y29.888
X-25.782Y29.938
X-25.748Y29.941
X-25.712Y29.949
X-25.Y30.
X25.001
X25.782Y29.938
X26.545Y29.755
X27.27Y29.455
X27.939Y29.045
X28.536Y28.536
X29.045Y27.939
X29.455Y27.27
X29.755Y26.545
X29.938Y25.782
X30.Y25.
Y-25.
X29.998Y-25.03
X29.949Y-25.712
X29.941Y-25.748
X29.938Y-25.782
X29.888Y-25.99
X29.797Y-26.409
X29.771Y-26.48
X29.755Y-26.545
X29.668Y-26.756
X29.548Y-27.077
X29.493Y-27.177
X29.455Y-27.27
X29.343Y-27.453
X29.206Y-27.703
X29.114Y-27.826
X29.045Y-27.939
X28.921Y-28.084
X28.779Y-28.274
X28.641Y-28.412
X28.536Y-28.536
X28.412Y-28.641
X28.274Y-28.779
X28.084Y-28.921
X27.939Y-29.045
X27.826Y-29.114
X27.703Y-29.206
X27.453Y-29.343
X27.27Y-29.455
X27.177Y-29.493
X27.077Y-29.548
X26.756Y-29.668
X26.545Y-29.755
X26.48Y-29.771
X26.409Y-29.797
X25.99Y-29.888
X25.782Y-29.938
X25.748Y-29.941
X25.712Y-29.949
X25.002Y-30.
X25.
X-25.
X-25.782Y-29.938
X-26.545Y-29.755
X-27.27Y-29.455
X-27.939Y-29.045
X-28.536Y-28.536
G3X-35.585Y-29.09I-3.247J-3.802
G1X-29.09Y-35.585
Z-17.143F600.
G3X-28.536Y-28.536I-3.247J3.802F2000.
G1X-29.045Y-27.939
X-29.455Y-27.27
X-29.755Y-26.545
X-29.938Y-25.782
X-30.Y-25.
Y25.001
X-29.949Y25.712
X-29.941Y25.748
X-29.938Y25.782
X-29.888Y25.99
X-29.797Y26.409
X-29.771Y26.48
X-29.755Y26.545
X-29.668Y26.756
X-29.548Y27.077
X-29.493Y27.177
X-29.455Y27.27
X-29.343Y27.453
X-29.206Y27.703
X-29.114Y27.826
X-29.045Y27.939
X-28.921Y28.084
X-28.779Y28.274
X-28.641Y28.412
X-28.536Y28.536
X-28.412Y28.641
X-28.274Y28.779
X-28.084Y28.921
X-27.939Y29.045
X-27.826Y29.114
X-27.703Y29.206
X-27.453Y29.343

X29.771Y-26.48
X29.755Y-26.545
X29.668Y-26.756
X29.548Y-27.077
X29.493Y-27.177
X29.455Y-27.27
X29.343Y-27.453
X29.206Y-27.703
X29.114Y-27.826
X29.045Y-27.939
X28.921Y-28.084
X28.779Y-28.274
X28.641Y-28.412
X28.536Y-28.536
X28.412Y-28.641
X28.274Y-28.779
X28.084Y-28.921
X27.939Y-29.045
X27.826Y-29.114
X27.703Y-29.206
X27.453Y-29.343
X27.27Y-29.455
X27.177Y-29.493
X27.077Y-29.548
X26.756Y-29.668
X26.545Y-29.755
Z-20.F600.
G3X-28.536Y-28.536I-3.247J3.802F2000.
G1X-29.045Y-27.939
X-29.455Y-27.27
X-29.755Y-26.545
X-29.938Y-25.782
X-30.Y-25.
Y25.001
X29.045Y27.939
X29.455Y27.27
X29.755Y26.545
X29.938Y25.782
X30.Y25.
Y-25.
X29.998Y-25.03
X25.
X-25.
X-25.782Y-29.938
X-26.545Y-29.755
X-27.27Y-29.455
X-27.939Y-29.045
X-28.536Y-28.536
G3X-35.585Y-29.09I-3.247J-3.802
G0Z-19.
Z10.
M09
M05
M30
%

%
(Date:03/30/07 Time:21:09:04)
G98G80G90G49G17
( / 52)
M6
S2500M3
G0X40.Y25.
G43Z10.H1
Z2.
G1Z-3.F2100.
Y30.
X35.
G3X30.Y25.I0.J-5.
G1Y-25.
G2X25.Y-30.I-5.J0.
G1X-25.
G2X-30.Y-25.I0.J5.
G1Y25.
G2X-25.Y30.I5.J0.
G1X25.
G2X30.Y25.I0.J-5.
G3X35.Y20.I5.J0.
G1X40.
Y25.
Z-6.
Y30.
X35.
G3X30.Y25.I0.J-5.
G1Y-25.
G2X25.Y-30.I-5.J0.
G1X-25.
G2X-30.Y-25.I0.J5.
G1Y25.
G2X-25.Y30.I5.J0.
G1X25.
G2X30.Y25.I0.J-5.
G3X35.Y20.I5.J0.
G1X40.
Y25.
Z-9.
Y30.
X35.
G3X30.Y25.I0.J-5.
G1Y-25.
G2X25.Y-30.I-5.J0.
G1X-25.
G2X-30.Y-25.I0.J5.
G1Y25.
G2X-25.Y30.I5.J0.
G1X25.
G2X30.Y25.I0.J-5.
G3X35.Y20.I5.J0.
G1X40.
Y25.
Z-12.
Y30.
X35.
G3X30.Y25.I0.J-5.
G1Y-25.
G2X25.Y-30.I-5.J0.
G1X-25.
G2X-30.Y-25.I0.J5.
G1Y25.
G2X-25.Y30.I5.J0.
G1X25.
G2X30.Y25.I0.J-5.
G3X35.Y20.I5.J0.
G1X40.
Y25.
Z-15.
Y30.
X35.
G3X30.Y25.I0.J-5.
G1Y-25.
G2X25.Y-30.I-5.J0.
G1X-25.
G2X-30.Y-25.I0.J5.
G1Y25.
G2X-25.Y30.I5.J0.
G1X25.
G2X30.Y25.I0.J-5.
G3X35.Y20.I5.J0.
G1X40.
Y25.
Z-18.
Y30.
X35.
G3X30.Y25.I0.J-5.
G1Y-25.
G2X25.Y-30.I-5.J0.
G1X-25.
G2X-30.Y-25.I0.J5.
G1Y25.
G2X-25.Y30.I5.J0.
G1X25.
G2X30.Y25.I0.J-5.
G3X35.Y20.I5.J0.
G1X40.
Y25.
Z-20.
Y30.
X35.
G3X30.Y25.I0.J-5.
G1Y-25.
G2X25.Y-30.I-5.J0.
G1X-25.
G2X-30.Y-25.I0.J5.
G1Y25.
G2X-25.Y30.I5.J0.
G1X25.
G2X30.Y25.I0.J-5.
G3X35.Y20.I5.J0.
G1X40.
Z10.
M5
T30M6
M30
%

[ 本帖最后由 liangantong 于 2007-4-9 07:41 编辑 ]

作者: 风之涯 时间: 2007-4-9 10:29
你的第二个程式没头啊，

作者: 风之涯 时间: 2007-4-9 10:30
还有

作者: 风之涯 时间: 2007-4-9 10:31
另外看看，你的结尾有没有M2，或M30

作者: 风之涯 时间: 2007-4-9 10:37
你的加工参数是不是一样的，我没细看，贴个图来看看，还有就是IJ为0时可以不用IJ，在POST里可以改的，还有就是MC的刀路一条线打断后会出两个刀路，（这一点MC倒应该向PTC多学学啦，不过MC可以用优化功能把程式做一下压缩），可能也有点影响，你可以自己查查看

[ 本帖最后由风之涯于 2007-4-9 10:46 编辑 ]

作者: liangantong 时间: 2007-4-10 06:49
风兄:感谢之余,非常感动!不但指教了,而且还说得很细.
我也要向你学习,多帮助别人(如有能力的话).

PROE是我接触的第一个CAD\CAM软件,所以对她有种特殊的感情,
以前没CAM基础,身边的人不懂,且都说她的NC不好,只学了她的CAD,
现有了MC基础,重燃了那一份迷恋.

好了,让我仔细学习,不懂的地方再请教.

作者: 风之涯 时间: 2007-4-10 12:03
客气，客气，我有什么不懂的，也请你多多指点，（我也只是瞎说一气）

作者: liangantong 时间: 2007-4-12 06:45
风兄：你用的是什么后处理？
有没有适合西门子802的？
谢谢！

作者: 风之涯 时间: 2007-4-12 13:03
802的我没用过，不知道是什么指令格式与其它机子有什么不同，后处理我也有些搞不定，特别是钻孔的固定循环，你可以把你所要的程式代码上传，让大家帮你改一个

[ 本帖最后由风之涯于 2007-4-12 13:06 编辑 ]

作者: 2362937 时间: 2007-4-12 14:55

原帖由 风之涯 于 2007-4-12 13:03 发表
802的我没用过，不知道是什么指令格式与其它机子有什么不同，后处理我也有些搞不定，特别是钻孔的固定循环，你可以把你所要的程式代码上传，让大家帮你改一个

老大说说钻孔的固定循环？

作者: liangantong 时间: 2007-4-12 20:40
不怕各位见笑,怎么才知道"我所需要的程式代码"?

通过开思论坛,增长了不少见识,感谢各位参与的人!

[ 本帖最后由 liangantong 于 2007-4-12 20:43 编辑 ]

作者: 风之涯 时间: 2007-4-12 21:00

原帖由 liangantong 于 2007-4-12 20:40 发表
不怕各位见笑,怎么才知道"我所需要的程式代码"?

通过开思论坛,增长了不少见识,感谢各位参与的人!

比如，西门子的圆弧插补用法为G2（3）X_Y_U_,三菱的用G2(3)X_Y_R_,
深孔钻:G83X_Y_R2=_R3=_~~~~~~~~~~______________G83X_Y_Z_R_Q_等,
这些控制器都有些差别的,做后处理时都要注意的,我说的是在G83里的R3我到现在也没搞定,不知道有没有高手能出手帮帮我!!

[ 本帖最后由风之涯于 2007-4-12 21:04 编辑 ]

作者: liangantong 时间: 2007-4-13 07:48
风兄:看来这些东西不是三两天能弄清楚的,病急乱求医,请你先把820的后处理搞一个给我,或许它们血缘相近，能用也说不准．无耐，无耐．．．．．．．

谢谢！

我的ＥＭＡＩＬ：a87477843@126.com

[ 本帖最后由 liangantong 于 2007-4-13 07:50 编辑 ]

欢迎光临 iCAx开思网 (https://www.icax.org/)