iCAx开思网

标题: 后处理输出问题(版主请进) [打印本页]

作者: jud125 时间: 2006-9-12 23:50
标题: 后处理输出问题(版主请进)
我想一次全部输出讯息可是只想一个TP输出一个同一把刀的讯息并判别该TP里最小Z和最小预留量,该如何修改呢
* define private variables:
FORMAT (COORDINATES) Zinit Clear Depth cleard depthd;
FORMAT (COORDINATES) maxz minz surftol sidestep downstep ;
*FORMAT (COORDINATES) tooldia cornerr tapera CUT_LENGTH ;
FORMAT (COORDINATES) tooldia cornerr tapera ;
*FORMAT (COORDINATES) XfirstOrigin YfirstOrigin ZfirstOrigin ;
*FORMAT (USER_1)    CurrSubNum ;
*FORMAT (coordinates) ORIGOLDI ORIGOLDJ ORIGOLDK ;
FORMAT (character) TP_NAME PROC_NAME CURR_NAME ;
* define private flags:
FORMAT (USER_2)    FlagSub FlagSeq FlagSpin;
FORMAT (USER_2)    FirstOriginChange FlagError Flagrotmac  ;
FORMAT (COORDINATES) unit maxzo minzo sideso downso  diao rado cuto clearo partto partoffo ;
FORMAT (COORDINATES) maxzop minzop ;
FORMAT (FEED)       feedo feedi ;
FORMAT (SPINDLE_SPEED) spino ;
* define private constants:
FORMAT (USER_2)    YES NO ;

********************************************************
NON_MODAL  ALL_VAR;
MODAL    X_CURPOS Y_CURPOS Z_CURPOS ;
MODAL    LIN_MOV CIRC_MOV MCH_FEED SPIN_SPEED SPIN_DIR MCH_COOL MCH_DWELL;
MODAL    CUTCOM_ON  CUTCOM_OFF Z_UP Z_DOWN;
MODAL    CYC_DEPTH CYC_PECK CYC_DWELL CYC_RETR CYC_CLEAR Depth Clear NURBS_MOV;
MODAL    sidestep surftol downstep PART_TOL SIDE_STEP DOWN_STEP ;

IDENTICAL  X_CURPOS X_ENDPT ;
IDENTICAL  Y_CURPOS Y_ENDPT ;

********************************************************
NEW_LINE_IS $ ;
   OUTPUT \J ;
********************************************************

BEGINNING OF TAPE:

*    OUTPUT $ "TPN,PRN,CMT,PRNU,MAXZ,MINZ,STOL,SIDS,DOST,TN,POS,TFEE,SPIN,DIA,R," ;
*    OUTPUT "TAPER,CUTL,CRL,PRTOF" ;
   OUTPUT $ "Toolpath Name,Procedure Name,Comment,Procedure Number,Maximum Z Height," ;
   OUTPUT "Minimum Z Height,Surface Tolerance,Sidestep,Downstep,Toolname,Holder Number," ;
   OUTPUT "Feedrate,Spindle Speed,Tool Diameter,Corner Radius,Taper Angle,Flute Length," ;
   OUTPUT "Clear Length,Part Offset" ;
   YES             = 1 ;
   NO             = 0 ;
   MCH_FEED       = 0 ;
   surftol       = 0.0 ;
   sidestep       = 0.0 ;
   downstep       = 0.0 ;
   unit          = 1.0 ;


*-----Unit matrix (MUST be input in this order !!!)
*    ROT_MAT1 = 1.0 ; ROT_MAT2 = 0.0 ; ROT_MAT3 = 0.0 ;
*    ROT_MAT4 = 0.0 ; ROT_MAT5 = 1.0 ; ROT_MAT6 = 0.0 ;
*    ROT_MAT7 = 0.0 ; ROT_MAT8 = 0.0 ; ROT_MAT9 = 1.0 ;

*--For the first origin change
* ORIGOLDI=0 ; ORIGOLDJ=0 ; ORIGOLDK=1 ;
* flagrotmac = no ;

*******************************************************************

print0 \j "copy " part_name "." tp_name "." post_name " " part_name "." tp_name ".csv" ;
print0 \j "del *." post_name;
print0 \j DBL_QUOTE "C:\Program Files\Microsoft Office\Office\EXCEL.EXE" DBL_QUOTE "/e " part_name "." tp_name ".csv" ;
print0 \j "del *." post_name;
print0 \j "del *.txt" ;
print0 \j "del print0.bat" ;

BEGINNING OF PROC:

   maxz = -9999.0 ;
   minz =  9999.0 ;
   feedi = 1 ;
   IF_SET (PFM_UNITS _EQ_ "MM")
   unit = 1.0 ;
   END_IF ;
   IF_SET (PFM_UNITS _EQ_ "INCH")
   unit = 1/25.4 ;
   END_IF ;


   KEEP PROC_NAME ;
   SET_ON MCH_COOL ;

BEGINNING OF TLPATH:
   SET_ON  LIN_MOV CIRC_MOV ;

END OF PROC:

**************************************************************
* Specify data ouput for each procedure type
**************************************************************

   IF_SET ( PROC_NAME _EQ_ "PROFILE" )
   FirstTool = CURR_TOOL ;
   LastTool  = CURR_TOOL ;
   OUTPUT $ TP_NAME "," PROC_NAME "," PROC_CMNT "," PROC_NUM "," maxzop "," minzop ",Not Applicable," sideso "," ;
   OUTPUT  downso "," CURR_NAME "," CURR_TOOL ","  feedo "," spino "," diao "," rado "," ;
   OUTPUT  CON_ANG "," cuto "," clearo ",Not Applicable" ;
   END_IF ;
   IF_SET ( PROC_NAME _EQ_ "POCKET" )
   FirstTool = CURR_TOOL ;
   LastTool  = CURR_TOOL ;
   OUTPUT $ TP_NAME "," PROC_NAME "," PROC_CMNT "," PROC_NUM "," maxzop "," minzop ",Not Applicable," sideso "," ;
   OUTPUT  downso "," CURR_NAME "," CURR_TOOL ","  feedo "," spino "," diao "," rado "," ;
   OUTPUT  CON_ANG "," cuto "," clearo ",Not Applicable" ;
   END_IF ;
   IF_SET ( PROC_NAME _EQ_ "WCUT" )
   FirstTool = CURR_TOOL ;
   LastTool  = CURR_TOOL ;
   OUTPUT $ TP_NAME "," PROC_NAME "," PROC_CMNT "," PROC_NUM "," maxzop "," minzo "," partto ",Not Available," ;
   OUTPUT  downso "," CURR_NAME "," CURR_TOOL ","  feedo "," spino "," diao "," rado "," ;
   OUTPUT  CON_ANG "," cuto "," clearo "," partoffo ;
   END_IF ;
   IF_SET ( PROC_NAME _EQ_ "ZCUT" )
   OUTPUT $ TP_NAME "," PROC_NAME "," PROC_CMNT "," PROC_NUM "," maxzop "," minzo "," partto "," sideso "," ;
   OUTPUT  downso "," CURR_NAME "," CURR_TOOL ","  feedo "," spino "," diao "," rado "," ;
   OUTPUT  CON_ANG "," cuto "," clearo "," partoffo ;
   END_IF ;
   IF_SET ( PROC_NAME _EQ_ "SURMIL" )
   OUTPUT $ TP_NAME "," PROC_NAME "," PROC_CMNT "," PROC_NUM "," maxzo "," minzo "," partto "," sideso ;
   OUTPUT  ",Not Applicable," CURR_NAME "," CURR_TOOL ","  feedo "," spino "," diao "," rado "," ;
   OUTPUT CON_ANG "," cuto "," clearo "," partoffo ;
   END_IF ;
   IF_SET ( PROC_NAME _EQ_ "SRFPKT" )
   OUTPUT $ TP_NAME "," PROC_NAME "," PROC_CMNT "," PROC_NUM "," maxzo "," minzo "," partto "," sideso ;
   OUTPUT  ",Not Applicable," CURR_NAME "," CURR_TOOL ","  feedo "," spino "," diao "," rado "," ;
   OUTPUT CON_ANG "," cuto "," clearo "," partoffo ;
   END_IF ;
   IF_SET ( PROC_NAME _EQ_ "SURCLR" )
   OUTPUT $ TP_NAME "," PROC_NAME "," PROC_CMNT "," PROC_NUM "," maxzo "," minzo "," partto "," sideso ;
   OUTPUT  ",Not Applicable," CURR_NAME "," CURR_TOOL ","  feedo "," spino "," diao "," rado "," ;
   OUTPUT CON_ANG "," cuto "," clearo "," partoffo ;
   END_IF ;
   IF_SET ( PROC_NAME _EQ_ "SRFPRF" )
   OUTPUT $ TP_NAME "," PROC_NAME "," PROC_CMNT "," PROC_NUM "," maxzo "," minzo "," partto "," sideso ;
   OUTPUT  ",Not Available," CURR_NAME "," CURR_TOOL ","  feedo "," spino "," diao "," rado "," ;
   OUTPUT CON_ANG "," cuto "," clearo "," partoffo ;
   END_IF ;
   IF_SET ( PROC_NAME _EQ_ "CURVE_MX" )
   OUTPUT $ TP_NAME "," PROC_NAME "," PROC_CMNT "," PROC_NUM "," maxzo "," minzo ",Not Applicable,Not Applicable" ;
   OUTPUT  ",Not Applicable," CURR_NAME "," CURR_TOOL ","  feedo "," spino "," diao "," rado "," ;
   OUTPUT CON_ANG "," cuto "," clearo ",Not Applicable" ;
   END_IF ;
   IF_SET ( PROC_NAME _EQ_ "RULED_MX" )
   OUTPUT $ TP_NAME "," PROC_NAME "," PROC_CMNT "," PROC_NUM "," maxzo "," minzo ",Not Applicable,Not Applicable" ;
   OUTPUT  ",Not Applicable," CURR_NAME "," CURR_TOOL ","  feedo "," spino "," diao "," rado "," ;
   OUTPUT CON_ANG "," cuto "," clearo ",Not Applicable" ;
   END_IF ;
   IF_SET ( PROC_NAME _EQ_ "REMACHIN" )
   OUTPUT $ TP_NAME "," PROC_NAME "," PROC_CMNT "," PROC_NUM "," maxzo "," minzo "," partto "," sideso "," ;
   OUTPUT  downso "," CURR_NAME "," CURR_TOOL ","  feedo "," spino "," diao "," rado "," ;
   OUTPUT  CON_ANG "," cuto "," clearo "," partoffo ;
   END_IF ;


********************************************************
*TOOL CHANGE: FIRST:
*    SET_ON  SPIN_SPEED SPIN_DIR ;
*-----save first tool number
*    FirstTool = CURR_TOOL ;
*    LastTool  = CURR_TOOL ;

*TOOL CHANGE:
*    SET_ON  SPIN_SPEED SPIN_DIR ;

*TOOL CHANGE: LAST:
*    SET_ON  SPIN_SPEED SPIN_DIR ;
*-----save last tool number
*    LastTool = CURR_TOOL ;

********************************************************
FEED:
   SET_ON MCH_FEED ;

********************************************************
*LINEAR MOTION: FAST:
*
*    SET_ON SPIN_SPEED SPIN_DIR ;
*    SET_ON CIRC_MOV NURBS_MOV ;
*    Xold = X_CURPOS ;
*    Yold = Y_CURPOS ;
*    Zold = Z_CURPOS ;

LINEAR MOTION:
   SET_ON SPIN_SPEED SPIN_DIR ;
   IF_SET (maxz _LT_ Z_CURPOS)
   maxz = Z_CURPOS ;
   END_IF ;
   IF_SET (minz _GT_ Z_CURPOS)
   minz = Z_CURPOS ;
   END_IF ;

*    SET_ON CIRC_MOV NURBS_MOV;
*    Xold = X_CURPOS ;
*    Yold = Y_CURPOS ;
*    Zold = Z_CURPOS ;

   IF_SET (feedi _LT_ MCH_FEED)
   feedi = MCH_FEED ;
   END_IF ;

作者: jud125 时间: 2006-9-12 23:51
*****************************
   maxzo  = maxz*unit;
   IF_SET ( PROC_NAME _NE_ "SURMIL" )
   IF_SET ( PROC_NAME _NE_ "SRFPRF" )
   IF_SET ( PROC_NAME _NE_ "SRFPKT" )
   IF_SET ( PROC_NAME _NE_ "SURCLR" )
   IF_SET ( PROC_NAME _NE_ "CURVE_MX" )
   IF_SET ( PROC_NAME _NE_ "RULED_MX" )
   IF_SET ( PROC_NAME _NE_ "REMACHIN" )
   maxzop  = Z_UP*unit;
   END_IF ;
   END_IF ;
   END_IF ;
   END_IF ;
   END_IF ;
   END_IF ;
   END_IF ;
   minzo  = minz*unit;
   IF_SET ( PROC_NAME _NE_ "SURMIL" )
   IF_SET ( PROC_NAME _NE_ "SRFPRF" )
   IF_SET ( PROC_NAME _NE_ "SRFPKT" )
   IF_SET ( PROC_NAME _NE_ "SURCLR" )
   IF_SET ( PROC_NAME _NE_ "CURVE_MX" )
   IF_SET ( PROC_NAME _NE_ "RULED_MX" )
   IF_SET ( PROC_NAME _NE_ "REMACHIN" )
   minzop  = Z_DOWN*unit;
   END_IF ;
   END_IF ;
   END_IF ;
   END_IF ;
   END_IF ;
   END_IF ;
   END_IF ;
   IF_SET ( PROC_NAME _NE_ "POCKET" )
   IF_SET ( PROC_NAME _NE_ "PROFILE" )
   IF_SET ( PROC_NAME _NE_ "CURVE_MX" )
   partto = PART_TOL*unit;
   END_IF ;
   END_IF ;
   END_IF ;
   IF_SET ( PROC_NAME _NE_ "RULED_MX" )
   sideso = SIDE_STEP*unit;
   END_IF ;
   IF_SET ( PROC_NAME _NE_ "SURMIL" )
   IF_SET ( PROC_NAME _NE_ "SRFPRF" )
   IF_SET ( PROC_NAME _NE_ "SRFPKT" )
   IF_SET ( PROC_NAME _NE_ "SURCLR" )
   IF_SET ( PROC_NAME _NE_ "CURVE_MX" )
   IF_SET ( PROC_NAME _NE_ "RULED_MX" )
   downso = DOWN_STEP*unit;
   END_IF ;
   END_IF ;
   END_IF ;
   END_IF ;
   END_IF ;
   END_IF ;
   feedo  = feedi*unit;
   spino  = SPIN_SPEED;
   diao = DIAMETER_*unit;
   rado = TOOL_RAD*unit;
   cuto = CUT_LENGTH*unit;
   clearo = CLEAR_LENG*unit;
   IF_SET ( PROC_NAME _NE_ "POCKET" )
   IF_SET ( PROC_NAME _NE_ "PROFILE" )
   partoffo = PART_OFST*unit;
   END_IF ;
   END_IF ;

********************************************************
*CIRCULAR MOTION:
*    SET_ON SPIN_SPEED SPIN_DIR ;
*
*    DXcenter = X_CENTER - Xold ;
*    DYcenter = Y_CENTER - Yold ;
*    DZcenter = Z_CENTER - Zold ;
*
*    SET_ON LIN_MOV NURBS_MOV ;
*    Xold = X_CURPOS ;
*    Yold = Y_CURPOS ;
*    Zold = Z_CURPOS ;

********************************************************
CYCLE: ON:
*    FlagSpin = NO ;
*    IF_SET (SPIN_SPEED) FlagSpin = YES ;
*    END_IF ;
*    IF_SET (SPIN_DIR) FlagSpin = YES ;
*    END_IF ;
*    IF_SET (FlagSpin _EQ_ YES) SET_ON SPIN_SPEED SPIN_DIR ;
*    END_IF ;

   SET_ON X_CURPOS Y_CURPOS Z_CURPOS ;
   SET_ON CYC_DEPTH CYC_RETR CYC_CLEAR MCH_FEED MCH_COOL ;
   SET_ON Zinit Depth Clear ;
   Zinit = Z_CURPOS + CYC_DZINIT ;
   Depth = Z_CURPOS - CYC_DEPTH ;
   Clear = Z_CURPOS + CYC_CLEAR ;

   SET_ON  LIN_MOV CIRC_MOV ;
   SET_OFF CYC_DEPTH CYC_CLEAR;
*    Xold = X_CURPOS ;
*    Yold = Y_CURPOS ;
*    Zold = Z_CURPOS ;

CYCLE:
   Depth = Z_CURPOS - CYC_DEPTH ;
   Clear = Z_CURPOS + CYC_CLEAR ;

   SET_ON  LIN_MOV CIRC_MOV ;
   SET_OFF CYC_DEPTH CYC_CLEAR;
*    Xold = X_CURPOS ;
*    Yold = Y_CURPOS ;
*    Zold = Z_CURPOS ;



CYCLE: OFF:
   IF_SET (PFM_UNITS _EQ_ "MM")
   unit = 1.0 ;
   END_IF ;
   IF_SET (PFM_UNITS _EQ_ "INCH")
   unit = 1/25.4;
   END_IF ;

   cleard = clear*unit;
   depthd = depth*unit;
   feedo  = feedi*unit;
   spino  = SPIN_SPEED;
   diao = DIAMETER_*unit;
   rado = TOOL_RAD*unit;
   cuto = CUT_LENGTH*unit;
   clearo = CLEAR_LENG*unit;

   IF_SET ( PROC_NAME _EQ_ "DRILL" )
   OUTPUT $ TP_NAME "," PROC_NAME "," PROC_CMNT "," PROC_NUM "," cleard "," Depthd ;
   OUTPUT ",Not Applicable,Not Applicable,Not Applicable," ;
   OUTPUT CURR_NAME "," CURR_TOOL ","  feedo "," spino "," diao "," rado ","  ;
   OUTPUT TOOL_ANGLE "," cuto "," clearo ",Not Applicable" ;
   END_IF ;

   SET_ON  LIN_MOV CIRC_MOV MCH_FEED ;
*    Zold = Zinit ;

********************************************************
*ORIGIN CHANGE:

*-----Save the first origin data for later use
* IF_SET (FirstOriginChange _EQ_ YES )
*    XfirstOrigin    = X_ORIGIN  ;
*    YfirstOrigin    = Y_ORIGIN  ;
*    ZfirstOrigin    = Z_ORIGIN  ;
*    FirstOriginChange = NO       ;
* END_IF ;

*.....distance between the rotation center and the ORIGIN
*    TRANS_MATX = X_ORIGIN - XfirstOrigin - X_MACH  ;
*    TRANS_MATY = Y_ORIGIN - YfirstOrigin - Y_MACH  ;
*    TRANS_MATZ = Z_ORIGIN - ZfirstOrigin - Z_MACH  ;

*.....check for change in orientation ( 4,5 axis positioining )
* FlagError  = NO ;
* Flagrotmac = no ;

* IF_SET ( I_ORIGIN _NE_ ORIGOLDI ) FLAGROTMAC = YES ; END_IF ;
* IF_SET ( J_ORIGIN _NE_ ORIGOLDJ ) FLAGROTMAC = YES ; END_IF ;
* IF_SET ( K_ORIGIN _NE_ ORIGOLDK ) FLAGROTMAC = YES ; END_IF ;

* IF_SET ( FLAGROTMAC _EQ_ YES )    FlagError  = YES ; END_IF ;

* IF_SET (FlagError _EQ_ YES)
*    PRINT  \J "Error: ucs rotation was found in:" ;
*    PRINT  \J "    TP=" TP_NAME " PROC=" PROC_NUM " (" PROC_NAME ")" ;
*    PRINT  \J "Error: Cannot post ucs rotation toolpaths" ;
*    OUTPUT \J " M00 (Error: ucs rotation was found)" ;
*    OUTPUT \J " M00 (TP=" TP_NAME " PROC=" PROC_NUM " - " PROC_NAME ")" ;
* END_IF ;

* ORIGOLDI = I_ORIGIN ;
* ORIGOLDJ = J_ORIGIN ;
* ORIGOLDK = K_ORIGIN ;

********************************************************
*AXISCHANGE:
* FlagError  = NO ;
* IF_SET (AXIS_NUM  _GT_ 3)       FlagError = YES ; END_IF ;

********************************************************

欢迎光临 iCAx开思网 (https://www.icax.org/)