iCAx开思网

标题: 请高手帮我改一下西门子后处理中的钻孔和攻丝 [打印本页]

作者: lifeng111 时间: 2006-1-11 14:15
标题: 请高手帮我改一下西门子后处理中的钻孔和攻丝
下面是我用西门子后处理文件可后处理出来的钻孔攻丝都不行请高手帮我改一下谢谢!
N1T1D1
N2M6
N3G90G54X0Y0G0
N4S1000M3
N5G0X0Y0Z20
N6X-304.8Y-101.6M8
N7Z8
N8G1Z7F500
N9F500
N10MCALL CYCLE83,0, 2(7, 5, -55, 10
N11X-304.8Y-101.6
N12MCALL
N13G0Z20
N14X-558.8
N15Z8
N16G1Z7
N17F500
N18MCALL CYCLE83,0, 2(7, 5, -55, 10
N19X-558.8Y-101.6
N20MCALL
N21G0Z20
N22X-457.2
N23Z8
N24G1Z7
N25F500
N26MCALL CYCLE83,0, 2(7, 5, -55, 10
N27X-457.2Y-101.6
N28MCALL
N29G0Z20
N30X-812.8
N31Z8
N32G1Z7
N33F500
N34MCALL CYCLE83,0, 2(7, 5, -55, 10
N35X-812.8Y-101.6
N36MCALL
N37G0Z20
N38X-711.2
N39Z8
N40G1Z7
N41F500
N42MCALL CYCLE83,0, 2(7, 5, -55, 10
N43X-711.2Y-101.6
N44MCALL
N45G0Z20
N46X-1066.8
N47Z8
N48G1Z7
N49F500
N50MCALL CYCLE83,0, 2(7, 5, -55, 10
N51X-1066.8Y-101.6
N52MCALL
N53G0Z20
N54X-965.2
N55Z8
N56G1Z7
N57F500
N58MCALL CYCLE83,0, 2(7, 5, -55, 10
N59X-965.2Y-101.6
N60MCALL
N61G0Z20
N62X-558.8Y101.6
N63Z8
N64G1Z7
N65F500
N66MCALL CYCLE83,0, 2(7, 5, -55, 10
N67X-558.8Y101.6
N68MCALL
N69G0Z20
N70X-457.2
N71Z8
N72G1Z7
N73F500
N74MCALL CYCLE83,0, 2(7, 5, -55, 10
N75X-457.2Y101.6
N76MCALL
N77G0Z20
N78Y203.2
N79Z8
N80G1Z7
N81F500
N82MCALL CYCLE83,0, 2(7, 5, -55, 10
N83X-457.2Y203.2
N84MCALL
N85G0Z20
N86X-558.8
N87Z8
N88G1Z7
N89F500
N90MCALL CYCLE83,0, 2(7, 5, -55, 10
N91X-558.8Y203.2
N92MCALL
N93G0Z20
N94M9
N95G54X0Y0
N96M5
N97M30

作者: qwert76 时间: 2018-7-29 15:30
谢谢谢谢谢谢

作者: dxfei3 时间: 2018-11-6 17:21
看看，向楼主学习。

作者: cj09812399 时间: 2019-8-7 03:13
你这后处理肯定不对，CYCLE83后面不能直接跟数字，数字应该在括号里才对

欢迎光临 iCAx开思网 (https://www.icax.org/)