iCAx开思网

标题: [分享]法兰克、三菱后处理源代码全“民”共享 [打印本页]

作者: sjhxs 时间: 2005-11-10 18:14
标题: [分享]法兰克、三菱后处理源代码全“民”共享
源代码有分享精神的不多，我来试吃“螃蟹”，请多多指教！

* DEMO 3 axes Post Processor for FANUC
* CIMATRON90 VER 9.0
* Last update : 23-FEB-1998

********************************************************
* define private variables:
FORMAT (SEQUENCING)  Seq SubSeq CNTRL_NUM NURBS_DEG count first deg ;
FORMAT (TOOL)       CutterComp FirstTool LastTool ;
FORMAT (COORDINATES) Xold Yold Zold DXcenter DYcenter DZcenter ;
FORMAT (COORDINATES) Zinit Clear Depth CNTRL_X  CNTRL_Y  CNTRL_Z  KNOT_ ;
FORMAT (COORDINATES) Xhome Yhome Zhome ;
FORMAT (COORDINATES) XfirstOrigin YfirstOrigin ZfirstOrigin ;
FORMAT (USER_1)    CurrSubNum ;
FORMAT (coordinates) ORIGOLDI ORIGOLDJ ORIGOLDK ;

* define private flags:
FORMAT (USER_2)    FlagSub FlagSeq FlagSpin;
FORMAT (USER_2)    FirstOriginChange FlagError Flagrotmac  ;

* define private constants:
FORMAT (USER_2)    YES NO ;

* change the format of existing variables:
FORMAT (USER_1)    SUB_NUMBER ;
FORMAT (COORDINATES) Time ;---定义时间变量

********************************************************
INTERACTION (USER_1)    "MAIN-PROGRAM-NUMBER"    MainNum    = 100  ;
INTERACTION (TOOL)       "DIACOMP=TOOL+<xx>"    DiaComp    = 50 ;
INTERACTION (USER_1)    "TOOL-CHANGE-PROGRAM"    ChangeTool  = 8000 ;
INTERACTION (CHARACTER) "SEQUENCING<Y/N>"       NumYN    = "N"  ;
INTERACTION (SEQUENCING) "SEQUENC-START"          SeqStart = 10 ;
INTERACTION (SEQUENCING) "SEQUENC-INCR."          SeqIncr    = 10 ;
INTERACTION (CHARACTER) "SUBROUTINES<Y/N>"       Sub       = "N"  ;
INTERACTION (USER_1)    "SUB-PROGRAM-NUMBER"    StartSubNum = 1000 ;

********************************************************
NON_MODAL  ALL_VAR;
MODAL    X_CURPOS Y_CURPOS Z_CURPOS ;
MODAL    LIN_MOV CIRC_MOV MCH_FEED SPIN_SPEED SPIN_DIR MCH_COOL MCH_DWELL;
MODAL    CUTCOM_ON  CUTCOM_OFF ;
MODAL    CYC_DEPTH CYC_PECK CYC_DWELL CYC_RETR CYC_CLEAR Depth Clear NURBS_MOV;

IDENTICAL  X_CURPOS X_ENDPT ;
IDENTICAL  Y_CURPOS Y_ENDPT ;

********************************************************
NEW_LINE_IS $ ;
   IF_SET (FlagSeq _EQ_ NO)
      OUTPUT \J ;
   ELSE
      IF_SET (FlagSub _EQ_ NO)
         OUTPUT \J "N" Seq ;
         Seq = Seq + SeqIncr ;
      ELSE
         OUTPUT \J "N" SubSeq ;
         SubSeq = SubSeq + SeqIncr ;
      END_IF ;
   END_IF ;

********************************************************
BEGINNING OF TAPE:
   YES             = 1 ;
   NO             = 0 ;
   Seq             = SeqStart ;

   FlagSeq = NO ;
   FlagSub = NO ;
   IF_SET (NumYN _EQ_ "y") FlagSeq = YES ; END_IF ;
   IF_SET (NumYN _EQ_ "Y") FlagSeq = YES ; END_IF ;

   IF_SET (Sub _EQ_ "y") Sub    = "Y" ; END_IF ;
   IF_SET (Sub _EQ_ "Y")
      SET_OFF NO_SUBROUT ;
   ELSE
      SET_ON  NO_SUBROUT ;
   END_IF ;

*-----Unit matrix (MUST be input in this order !!!)
   ROT_MAT1 = 1.0 ; ROT_MAT2 = 0.0 ; ROT_MAT3 = 0.0 ;
   ROT_MAT4 = 0.0 ; ROT_MAT5 = 1.0 ; ROT_MAT6 = 0.0 ;
   ROT_MAT7 = 0.0 ; ROT_MAT8 = 0.0 ; ROT_MAT9 = 1.0 ;

*-----shift all data according to the MCHINE ZERO indicated by the
*    user in the POSTPR interaction
   TRANS_MATX = 0 - X_MACH  ;
   TRANS_MATY = 0 - Y_MACH  ;
   TRANS_MATZ = 0 - Z_MACH  ;

*-----shift the HOME according to the MCHINE ZERO indicated by the
*    user in the POSTPR interaction
   Xhome = X_HOME - X_MACH  ;
   Yhome = Y_HOME - Y_MACH  ;
   Zhome = Z_HOME - Z_MACH  ;

*-----tool location is HOME
   Xold = X_HOME ;
   Yold = Y_HOME ;
   Zold = Z_HOME ;

*-----For 1st ORIGIN CHANGE
   FirstOriginChange = YES ;

   MCH_FEED = 9999 ;

*-----output
   IF_SET (FlagSeq _EQ_ YES )
      OUTPUT "%" \J;
   ELSE
      OUTPUT " %" \J;
   END_IF ;

*--For the first origin change
ORIGOLDI=0 ; ORIGOLDJ=0 ; ORIGOLDK=1 ;
flagrotmac = no ;

Time=0.001; 定义初始值

BEGINNING OF PROC:
   KEEP PROC_NAME ;
   SET_ON MCH_COOL ;
   FlagSub = NO ;
   SubSeq  = SeqStart ;

END OF PROC:
   Time = Time + N_GEN_TIME;

END OF TAPE:
   IF_SET (FirstTool _NE_ LastTool)
      OUTPUT $ " T" NEXT_TOOL " M98 P" ChangeTool;
   END_IF ;
   OUTPUT $ " M09 " ;
   OUTPUT $ " M30 " ;


END OF FILE:
   IF_SET (FlagSeq _EQ_ YES )
      OUTPUT \J "%" ;
   ELSE
      OUTPUT \J " %" ;
   END_IF ;
   OUTPUT  "(估计工时:" Time " 分钟)" ; 有没有办法帮偶搞到程序头？
********************************************************
FEED:
   KEEP MCH_FEED ;

SPIN:
   KEEP SPIN_SPEED ;

COOLANT:
   KEEP MCH_COOL ;

DWELL:
   KEEP MCH_DWELL ;

CUTTER COMPENSATION:
   KEEP  CUTCOM_ON ;

CUTTER COMPENSATION: COFF:
   KEEP  CUTCOM_OFF ;

********************************************************
TOOL CHANGE: FIRST:
   SET_ON  SPIN_SPEED SPIN_DIR ;
*-----save first tool number
   FirstTool = CURR_TOOL ;
   LastTool  = CURR_TOOL ;

*-----tool cutter compensation register number
   CutterComp = CURR_TOOL +  DiaComp ;

*-----assuming 1st tool is in the spindle, there is no need
*    for tool change)
   OUTPUT $ " T" CURR_TOOL ;
*-----more then one tool in this run of the Post Processor
   IF_SET (NEXT_TOOL _NE_ CURR_TOOL)
      OUTPUT $ " T" NEXT_TOOL ;
   END_IF ;
*-----standard tool change commands. (assuming 1st tool is in
   OUTPUT $ " G90 G80 G00 G17 G40 G54" ;
   OUTPUT $ "( 刀具名称---" CURR_NAME "×" CLEAR_LENG ")";
   OUTPUT $ "( 曲面偏移=" PART_OFST " 曲面公差=" PART_TOL" 轮廓偏移=" CONT_OFST " 轮廓公差=" CONT_TOL " )";
   OUTPUT $ "( 程式名称=" TP_NAME "本程式由" USER_NAME "编制 )";
   OUTPUT $ " Z" Zhome " S" SPIN_SPEED " " SPIN_DIR ;    (以上红色部分为程序头，双引号间内容可根据个人喜好修改）

TOOL CHANGE:
   SET_ON  SPIN_SPEED SPIN_DIR ;

*-----tool cutter compensation register number
   CutterComp = CURR_TOOL +  DiaComp ;

*-----tool change command (by using an internal tool change
*    subroutine)
   OUTPUT $ " T" CURR_TOOL " M98 P"  ChangeTool ;
   OUTPUT $ " T" NEXT_TOOL ;
*-----standard tool change commands. (assuming 1st tool is in
   OUTPUT $ " G90 G80 G00 G17 G40 G54" ;
   OUTPUT $ "( 刀具名称---" CURR_NAME "×" CLEAR_LENG ")";
   OUTPUT $ "( 曲面偏移=" PART_OFST " 曲面公差=" PART_TOL" 轮廓偏移=" CONT_OFST " 轮廓公差=" CONT_TOL " )";
   OUTPUT $ "( 程式名称=" TP_NAME "本程式由" USER_NAME "编制 )";
   OUTPUT $ " Z" Zhome " S" SPIN_SPEED " " SPIN_DIR ;

TOOL CHANGE: LAST:
   SET_ON  SPIN_SPEED SPIN_DIR ;
*-----save last tool number
   LastTool = CURR_TOOL ;

*-----tool cutter compensation register number
   CutterComp = CURR_TOOL +  DiaComp ;

   OUTPUT $ " T" CURR_TOOL " M98 P"  ChangeTool ;
*-----the last tool is the same as the first tool
   IF_SET (NEXT_TOOL _NE_ CURR_TOOL)
      OUTPUT $ " T" NEXT_TOOL ;
   END_IF ;
*-----standard tool change commands. (assuming 1st tool is in
   OUTPUT $ " G90 G80 G00 G17 G40 G54" ;
   OUTPUT $ "( 刀具名称---" CURR_NAME "×" CLEAR_LENG ")";
   OUTPUT $ "( 曲面偏移=" PART_OFST " 曲面公差=" PART_TOL" 轮廓偏移=" CONT_OFST " 轮廓公差=" CONT_TOL " )";
   OUTPUT $ "( 程式名称=" TP_NAME "本程式由" USER_NAME "编制 )";
   OUTPUT $ " Z" Zhome " S" SPIN_SPEED " " SPIN_DIR ;

[ 本帖最后由 sjhxs 于 2005-11-27 19:00 编辑 ]

作者: sjhxs 时间: 2005-11-10 18:14
********************************************************
LINEAR MOTION: FAST:
   FlagSpin = NO ;
   IF_SET (SPIN_SPEED) FlagSpin = YES ; END_IF ;
   IF_SET (SPIN_DIR) FlagSpin = YES ; END_IF ;
   IF_SET (FlagSpin _EQ_ YES)
      SET_ON SPIN_SPEED SPIN_DIR ;
      OUTPUT $ " S" SPIN_SPEED " " SPIN_DIR ;
   END_IF ;

   OUTPUT $ ;
   IF_SET (LIN_MOV)  OUTPUT " " LIN_MOV ; END_IF ;
   IF_SET (X_CURPOS) OUTPUT " X" X_CURPOS ; END_IF ;
   IF_SET (Y_CURPOS) OUTPUT " Y" Y_CURPOS ; END_IF ;
   IF_SET (Z_CURPOS) OUTPUT " Z" Z_CURPOS ; END_IF ;
   IF_SET (MCH_COOL) OUTPUT  " " MCH_COOL ; END_IF ;
   SET_ON CIRC_MOV NURBS_MOV ;
   Xold = X_CURPOS ;
   Yold = Y_CURPOS ;
   Zold = Z_CURPOS ;

LINEAR MOTION:
   FlagSpin = NO ;
   IF_SET (SPIN_SPEED) FlagSpin = YES ; END_IF ;
   IF_SET (SPIN_DIR) FlagSpin = YES ; END_IF ;
   IF_SET (FlagSpin _EQ_ YES)
      SET_ON SPIN_SPEED SPIN_DIR ;
      OUTPUT $ " S" SPIN_SPEED " " SPIN_DIR ;
   END_IF ;

   OUTPUT $ ;
   IF_SET (LIN_MOV) OUTPUT " "  LIN_MOV ; END_IF ;
   IF_SET (CUTCOM_ON)  OUTPUT " "  CUTCOM_ON " D" CutterComp ; END_IF ;
   IF_SET (CUTCOM_OFF) OUTPUT " "  CUTCOM_OFF ; END_IF ;
   IF_SET (X_CURPOS) OUTPUT " X" X_CURPOS ; END_IF ;
   IF_SET (Y_CURPOS) OUTPUT " Y" Y_CURPOS ; END_IF ;
   IF_SET (Z_CURPOS) OUTPUT " Z" Z_CURPOS ; END_IF ;
   IF_SET (MCH_FEED) OUTPUT " F" MCH_FEED ; END_IF ;
   IF_SET (MCH_COOL) OUTPUT  " " MCH_COOL ; END_IF ;
   SET_ON CIRC_MOV NURBS_MOV;
   Xold = X_CURPOS ;
   Yold = Y_CURPOS ;
   Zold = Z_CURPOS ;

********************************************************
CIRCULAR MOTION:
   FlagSpin = NO ;
   IF_SET (SPIN_SPEED) FlagSpin = YES ; END_IF ;
   IF_SET (SPIN_DIR) FlagSpin = YES ; END_IF ;
   IF_SET (FlagSpin _EQ_ YES)
      SET_ON SPIN_SPEED SPIN_DIR ;
      OUTPUT $ " S" SPIN_SPEED " " SPIN_DIR ;
   END_IF ;

   DXcenter = X_CENTER - Xold ;
   DYcenter = Y_CENTER - Yold ;
   DZcenter = Z_CENTER - Zold ;
   OUTPUT $ ;
   IF_SET (CIRC_MOV)       OUTPUT " " CIRC_MOV  ; END_IF ;
   IF_SET (X_CURPOS)       OUTPUT " X" X_ENDPT  ; END_IF ;
   IF_SET (Y_CURPOS)       OUTPUT " Y" Y_ENDPT  ; END_IF ;
   IF_SET (Z_CURPOS)       OUTPUT " Z" Z_ENDPT  ; END_IF ;
   IF_SET (DXcenter _NE_ 0.0) OUTPUT " I" DXcenter ; END_IF ;
   IF_SET (DYcenter _NE_ 0.0) OUTPUT " J" DYcenter ; END_IF ;
   IF_SET (DZcenter _NE_ 0.0) OUTPUT " K" DZcenter ; END_IF ;
   IF_SET (MCH_FEED)       OUTPUT " F" MCH_FEED ; END_IF ;
   IF_SET (MCH_COOL)       OUTPUT  " " MCH_COOL ; END_IF ;
   SET_ON LIN_MOV NURBS_MOV ;
   Xold = X_CURPOS ;
   Yold = Y_CURPOS ;
   Zold = Z_CURPOS ;
******************************************************************
NURBS MOTION: START:
OUTPUT $ NURBS_MOV "P" NURBS_DEG ;
count = 0;
first = 1;
SET_ON MCH_FEED;
NURBS MOTION:
IF_SET (first _EQ_ 1)
OUTPUT "K" KNOT_ "X" CNTRL_X "Y" CNTRL_Y "Z" CNTRL_Z "F" MCH_FEED;
END_IF;
IF_SET (first _EQ_ 0)
OUTPUT $ "K" KNOT_ "X" CNTRL_X "Y" CNTRL_Y "Z" CNTRL_Z;
END_IF;
first = 0;
NURBS MOTION: END:
deg = NURBS_DEG ;
REPEAT
count = count + 1 ;
OUTPUT $ "K" KNOT_ ;
UNTIL (count _EQ_ deg) ;
SET_ON LIN_MOV CIRC_MOV MCH_FEED;
********************************************************
INSERT WITH:
   OUTPUT $ INS_STR ;

INSERT WITHOUT:
   OUTPUT  \J INS_STR ;

MESSAGE:
   OUTPUT $ "( " MESS_STR " )"  ;

********************************************************
CYCLE: ON:
   FlagSpin = NO ;
   IF_SET (SPIN_SPEED) FlagSpin = YES ; END_IF ;
   IF_SET (SPIN_DIR) FlagSpin = YES ; END_IF ;
   IF_SET (FlagSpin _EQ_ YES)
      SET_ON SPIN_SPEED SPIN_DIR ;
      OUTPUT $ " S" SPIN_SPEED " " SPIN_DIR ;
   END_IF ;

   SET_ON X_CURPOS Y_CURPOS Z_CURPOS ;
   SET_ON CYC_DEPTH CYC_RETR CYC_CLEAR MCH_FEED MCH_COOL ;
   SET_ON Zinit Depth Clear ;
   Zinit = Z_CURPOS + CYC_DZINIT ;
   Depth = Z_CURPOS - CYC_DEPTH ;
   Clear = Z_CURPOS + CYC_CLEAR ;
   IF_SET (Zold _LT_ Zinit)
                     OUTPUT $ " Z" Zinit ;
      ELSE
                     OUTPUT $ " Z" Zold ;
      END_IF ;
                     OUTPUT $ ;
                     OUTPUT " "  CYC_RETR ;
                     OUTPUT " "  CYC_CODE ;
                     OUTPUT " X" X_CURPOS ;
                     OUTPUT " Y" Y_CURPOS ;
                     OUTPUT " Z" Depth ;
                     OUTPUT " R" Clear ;
   IF_SET (CYC_PECK)  OUTPUT " Q" CYC_PECK  ; END_IF ;
   IF_SET (CYC_DWELL) OUTPUT " P" CYC_DWELL ; END_IF ;
   IF_SET (CYC_XSHFT) OUTPUT " I" CYC_XSHFT ; END_IF ;
   IF_SET (CYC_YSHFT) OUTPUT " J" CYC_YSHFT ; END_IF ;
                     OUTPUT " F" MCH_FEED ;
                     OUTPUT " "  MCH_COOL ;
   SET_ON  LIN_MOV CIRC_MOV ;
   SET_OFF CYC_DEPTH CYC_CLEAR;
   Xold = X_CURPOS ;
   Yold = Y_CURPOS ;
   Zold = Z_CURPOS ;

CYCLE:
   Depth = Z_CURPOS - CYC_DEPTH ;
   Clear = Z_CURPOS + CYC_CLEAR ;
   OUTPUT $ ;
   IF_SET (CYC_RETR) OUTPUT " "  CYC_RETR ; END_IF ;
   IF_SET (X_CURPOS) OUTPUT " X" X_CURPOS ; END_IF ;
   IF_SET (Y_CURPOS) OUTPUT " Y" Y_CURPOS ; END_IF ;
   IF_SET (Depth)    OUTPUT " Z" Depth    ; END_IF ;
   IF_SET (Clear)    OUTPUT " R" Clear    ; END_IF ;
   IF_SET (CYC_PECK) OUTPUT " Q" CYC_PECK ; END_IF ;
   IF_SET (CYC_DWELL)  OUTPUT " P" CYC_DWELL  ; END_IF ;
   IF_SET (CYC_XSHFT)  OUTPUT " I" CYC_XSHFT  ; END_IF ;
   IF_SET (CYC_YSHFT)  OUTPUT " J" CYC_YSHFT  ; END_IF ;
   IF_SET (SPIN_SPEED) OUTPUT " S" SPIN_SPEED ; END_IF ;
   IF_SET (SPIN_DIR) OUTPUT " "  SPIN_DIR ; END_IF ;
   IF_SET (MCH_FEED) OUTPUT " F" MCH_FEED ; END_IF ;
   IF_SET (MCH_COOL) OUTPUT " "  MCH_COOL ; END_IF ;
   SET_ON  LIN_MOV CIRC_MOV ;
   SET_OFF CYC_DEPTH CYC_CLEAR;
   Xold = X_CURPOS ;
   Yold = Y_CURPOS ;
   Zold = Z_CURPOS ;

CYCLE: OFF:
   OUTPUT $ " G80 Z" Zinit ;
   SET_ON  LIN_MOV CIRC_MOV ;
   Zold = Zinit ;

********************************************************
ORIGIN CHANGE:

*-----Save the first origin data for later use
IF_SET (FirstOriginChange _EQ_ YES )
      XfirstOrigin    = X_ORIGIN  ;
      YfirstOrigin    = Y_ORIGIN  ;
      ZfirstOrigin    = Z_ORIGIN  ;
      FirstOriginChange = NO       ;
END_IF ;

*.....distance between the rotation center and the ORIGIN
   TRANS_MATX = X_ORIGIN - XfirstOrigin - X_MACH  ;
   TRANS_MATY = Y_ORIGIN - YfirstOrigin - Y_MACH  ;
   TRANS_MATZ = Z_ORIGIN - ZfirstOrigin - Z_MACH  ;
*    SET_OFF CIR_INTERP ; （去除 * 号则不输出G02、G03）
*.....check for change in orientation ( 4,5 axis positioining )
FlagError  = NO ;
Flagrotmac = no ;

IF_SET ( I_ORIGIN _NE_ ORIGOLDI ) FLAGROTMAC = YES ; END_IF ;
IF_SET ( J_ORIGIN _NE_ ORIGOLDJ ) FLAGROTMAC = YES ; END_IF ;
IF_SET ( K_ORIGIN _NE_ ORIGOLDK ) FLAGROTMAC = YES ; END_IF ;

IF_SET ( FLAGROTMAC _EQ_ YES )    FlagError  = YES ; END_IF ;

IF_SET (FlagError _EQ_ YES)
   PRINT  \J "Error: ucs rotation was found in:" ;
   PRINT  \J "    TP=" TP_NAME " PROC=" PROC_NUM " (" PROC_NAME ")" ;
   PRINT  \J "Error: Cannot post ucs rotaion toolpaths" ;
   OUTPUT \J " M00 (Error: ucs rotation was found)" ;
   OUTPUT \J " M00 (TP=" TP_NAME " PROC=" PROC_NUM " - " PROC_NAME ")" ;
END_IF ;

ORIGOLDI = I_ORIGIN ;
ORIGOLDJ = J_ORIGIN ;
ORIGOLDK = K_ORIGIN ;

********************************************************
AXISCHANGE:
FlagError  = NO ;
IF_SET (AXIS_NUM  _GT_ 3)       FlagError = YES ; END_IF ;

IF_SET (FlagError _EQ_ YES)
   PRINT  \J "Error: 4/5 axes motion was found in:" ;
   PRINT  \J "    TP=" TP_NAME " PROC=" PROC_NUM " (" PROC_NAME ")" ;
   PRINT  \J "Error: Cannot post 5 axes toolpaths" ;
   OUTPUT \J " M00 (Error: 4/5 axes motion was found)" ;
   OUTPUT \J " M00 (TP=" TP_NAME " PROC=" PROC_NUM " - " PROC_NAME ")" ;

END_IF ;

********************************************************
SUBROUTINE CALL:
   CurrSubNum = SUB_NUMBER + StartSubNum ;
   OUTPUT $ " M98 P" CurrSubNum  ;

BEGINNING OF SUB:
   SET_ON  MCH_FEED MCH_COOL LIN_MOV CIRC_MOV ;
   FlagSub = YES ;
   OUTPUT \J " " ;
   IF_SET (FlagSeq _EQ_ YES)
      OUTPUT \J "O" CurrSubNum ;
   ELSE
      OUTPUT \J " O" CurrSubNum ;
   END_IF ;

END OF SUB:
   OUTPUT $  " M99" ;
   FlagSub = NO ;

SUBROUTINE RETURN:
   SET_ON LIN_MOV CIRC_MOV X_CURPOS Y_CURPOS Z_CURPOS;

********************************************************

作者: 13131 时间: 2005-11-10 18:49
还是HJXHS兄实在.祝早点上班.

作者: leehongsheng 时间: 2005-11-10 18:50
老兄精神可嘉,顶

作者: yhhyhh 时间: 2005-11-10 21:07
精神可嘉

作者: tch21st 时间: 2005-11-10 21:13
支持源文件！

作者: jh0417 时间: 2005-11-10 21:31
虽然不懂还是要顶!!!!!!

作者: 忘了叫啥名 时间: 2005-11-10 22:57
最好是在源代码重要输出段加上注释，这样好点。

作者: szhaoran 时间: 2005-11-15 23:15
好

作者: wrg1975@163.com 时间: 2005-11-16 10:03
精神可嘉!!!
强烈支持!!!

作者: wizard22 时间: 2005-11-27 00:47
标题: ff
dad

作者: ijldx 时间: 2005-11-27 01:24
精神可嘉!!!
强烈支持!!!

作者: liang11111 时间: 2005-11-27 01:58
支持！鼎力支持！无私的精神！

作者: kilter_chen 时间: 2005-11-27 16:32
支持！鼎力支持！无私的精神！

作者: liutongxu 时间: 2005-11-28 15:04
ding

作者: 飞扬_WZ 时间: 2005-11-28 15:38

要顶！

作者: 星球大战 时间: 2006-1-4 21:47
看看

作者: wylxl2001 时间: 2006-1-8 08:32
谢谢

作者: 4673430 时间: 2006-1-8 12:59
祝早点上班!!!
OUTPUT "(估计工时:" Time " 分钟)" ; 有没有办法帮偶搞到程序头？
我也为这事烦恼!

作者: sjhxs 时间: 2006-1-8 13:31

原帖由 4673430 于 2006-1-8 12:59 发表
祝早点上班!!!
OUTPUT "(估计工时:" Time " 分钟)" ; 有没有办法帮偶搞到程序头？
我也为这事烦恼!

  由于顺序排列原因，这问题很难在EXF文件中实现，不过将TOOLS文件整合到NC文件中，倒也是办法之一。
将TOOLS输出打开并将EXF文件中的批处理内容修改成：
   PRINT0 \J "@ECHO OFF" ;
   PRINT0 \J "MD  D:\NC\" PART_NAME ;
   PRINT0 \J "COPY " PART_NAME "." TP_NAME ".TOOLS  D: \NC\" PART_NAME "\" TP_NAME ".NC " ;
   PRINT0 \J "TYPE " PART_NAME "." TP_NAME ".SJH >> D: \NC\" PART_NAME "\" TP_NAME ".NC" ;
   PRINT0 \J "DEL " PART_NAME "." TP_NAME ".*" ;

红色字为你的后处理名，如果要TOOLS显示在NC文件后面，则TOOLS 与SJH 对调即可

[ 本帖最后由 sjhxs 于 2006-1-8 13:46 编辑 ]

作者: 星球大战 时间: 2006-1-8 20:00
不是很完整，这样的后处理用了很危险
不过还是支持共享

作者: lby 时间: 2006-1-9 09:29
谢谢楼住！

作者: ldh888999 时间: 2006-1-9 10:15
cimatrom it 的刀具号在那改啊????怎么没有啊 ?????~帮帮忙急啊??~~~~我做的机子带刀库?~~~

作者: 4673430 时间: 2006-1-9 21:06

原帖由 sjhxs 于 2006-1-8 05:31 发表

  由于顺序排列原因，这问题很难在EXF文件中实现，不过将TOOLS文件整合到NC文件中，倒也是办法之一。
将TOOLS输出打开并将EXF文件中的批处理内容修改成：
   PRINT0 \J "@ECHO OFF" ;
   PR ...

谢谢楼主！

作者: xhoo888 时间: 2006-8-5 21:40
9494

作者: tantiduo 时间: 2006-8-5 22:14
这个我有了。

作者: julle 时间: 2006-8-6 16:36
精神伟大

作者: ning11 时间: 2006-8-6 19:11
支持！
鼎力支持！
无私的精神！

作者: LXH-0216772 时间: 2006-8-22 15:13
能不能把EXF文件发上来，我改了一下，老是出错报警

作者: lzhly2006 时间: 2006-8-22 16:39
好,学习学习下

作者: chenjiaqi147 时间: 2018-3-23 19:08
谢谢分享

作者: 游人朱 时间: 2018-9-15 11:57
牛逼啊

欢迎光临 iCAx开思网 (https://www.icax.org/)