iCAx开思网

标题: Point From File [打印本页]

作者: blackbird111 时间: 2004-8-19 01:16
标题: Point From File
ROW1
23.7372 0.4500 20
23.6200 2.4826 20
23.3536 4.9640 20
22.8289 7.4176 20
22.0660 9.8244 20
20.9872 12.1170 20
19.6780 14.2969 20
18.1133 16.3093 20
16.2139 18.0074 20
14.1049 19.4137 20
11.8622 20.5460 20
9.5360 21.4182 20
7.1837 22.1092 20
4.8145 22.6507 20
2.4193 23.0180 20
0.0000 23.1293 20
ROW2
22.7475 0.4500 22
22.6597 2.3816 22
22.3768 4.7563 22
21.8553 7.1012 22
21.1409 9.4125 22
20.1366 11.6259 22
18.8943 13.7275 22
17.4085 15.6747 22
15.6072 17.3335 22
13.5884 18.7029 22
11.4334 19.8032 22
9.1878 20.6362 22
6.9171 21.2887 22
4.6303 21.7840 22
2.3229 22.1012 22
0.0000 22.2444 22
ROW3
21.8172 0.4500 24
21.7482 2.2858 24
21.4613 4.5617 24
20.9707 6.8138 24
20.2766 9.0277 24
19.3054 11.1460 24
18.1273 13.1703 24
16.7117 15.0473 24
15.0239 16.6858 24
13.0857 18.0109 24
11.0255 19.0968 24
8.8561 19.8910 24
6.6641 20.5099 24
4.4580 20.9734 24
2.2362 21.2757 24
0.0000 21.3836 24
ROW4
20.9420 0.4500 26
20.8901 2.1956 26
20.6077 4.3803 26
20.1184 6.5369 26
19.4483 8.6590 26
18.5366 10.7021 26
17.4103 12.6493 26
16.0565 14.4573 26
14.4336 16.0301 26
12.6257 17.3778 26
10.6384 18.4263 26
8.5522 19.2087 26
6.4365 19.8096 26
4.2963 20.2125 26
2.1521 20.4755 26
0.0000 20.5582 26
ROW5
20.1141 0.4500 28
20.0622 2.1086 28
19.7984 4.2083 28
19.3137 6.2754 28
18.6905 8.3216 28
17.8069 10.2808 28
16.6961 12.1304 28
15.4079 13.8734 28
13.8884 15.4246 28
12.1685 16.7485 28
10.2684 17.7853 28
8.2623 18.5575 28
6.2211 19.1467 28
4.1507 19.5274 28
2.0751 19.7432 28
0.0000 19.8352 28
ROW6
19.3300 0.4500 30
19.2543 2.0237 30
19.0137 4.0415 30
18.5481 6.0266 30
17.9216 7.9792 30
17.0809 9.8617 30
16.0178 11.6376 30
14.7839 13.3115 30
13.3457 14.8219 30
11.7164 16.1262 30
9.9152 17.1737 30
7.9863 17.9374 30
6.0144 18.5104 30
4.0149 18.8887 30
2.0046 19.0726 30
0.0000 19.1501 30

如上所示点数据,用Insert_Free Form Feature_Through Points_Point From File直接生成曲面, 需要注意的是 ROW1~6,字母必须大写，这一点帮助文件上的事例是错误的。

长时间不用自己都忘记了，又折腾了许久。

作者: blackbird111 时间: 2004-8-19 03:25
还有一个问题，如下圆弧：
x    y    z    r
0 0.2    1 10
0.1  0    2 12
0 0.1 3    13

全部为0~90度，如何用数据表读入？是不是要二次开发？
记得pro/e可以直接读入。

欢迎光临 iCAx开思网 (https://www.icax.org/)