iCAx开思网

标题: Cimatron E5.02中文版，怎样输出中间文件 [打印本页]

作者: zhangcanwei 时间: 2004-3-30 21:05
标题: Cimatron E5.02中文版，怎样输出中间文件
我们单位刚买了Cimatron E5.02中文正式版，但是，不知道怎样输出中间文件。以前的外挂后置处理程序没办法用了，培训老师也没办法导出中间文件。
那位好人指点指点，万分感谢！！

作者: yyy.wx 时间: 2004-3-31 00:02
中间文件？不明白

作者: zhangcanwei 时间: 2004-3-31 09:14
      我是用ug的，UG可以输出后缀为cls的中间文件，可以用第三方的后置处理程序进行处理。我厂用的全是第三方的后置处理程序。
      Cimatron E5.0以前的版本可以输出类似于UG的cls的中间文件。
      因为我厂有好几台很特殊的机床，所以后置处理程序都是用VB重新编制的，急需导出中间文件。

作者: RAY 时间: 2004-3-31 09:31
USE IMPOST 成生 .APT FILE.

SOULD BE THE SAME THING.

TOOL XX  , TOOL,XX
TLDATA/MILL,10.0000,5.0000,75.0000,0.0000,0.0000
MSYS/158.7500,31.7500,50.8000,1.0000000,0.0000000,0.0000000,0.0000000,1.0000000,0.0000000
PAINT/PATH
PAINT/SPEED,10

LOAD/TOOL,1
SPINDL/RPM,100,CLW
COOLNT/FLOOD
PAINT/COLOR,186
RAPID
GOTO/-127.6618,136.7055,30.0000,0.0000000,0.0000000,1.0000000

RAPID
GOTO/-127.6618,136.7055,2.5400
PAINT/COLOR,42
FEDRAT/MMPM,36.0000
GOTO/-126.2491,136.9759,2.1546

GOTO/-124.6974,138.0341,1.6513
GOTO/-123.6231,139.8295,1.0907
GOTO/-123.4242,141.6971,0.5874
GOTO/-123.9852,143.4896,0.0842
GOTO/-125.2133,144.9106,-0.4191
GOTO/-126.9056,145.7254,-0.9223

作者: sword-kent 时间: 2004-3-31 09:34

RAY wrote:
USE IMPOST 成生 .APT FILE.
  
  SOULD BE THE SAME THING.
  
   TOOL XX  , TOOL,XX
    TLDATA/MILL,10.0000,5.0000,75.0000,0.0000,0.0000
    MSYS/158.7500,31.7500,50.8000,1.0000000,0.0000000,0.0000000,0.0000000,1.0000000,0.0000000
   &nbspAINT/PATH
   &nbspAINT/SPEED,10
  
    LOAD/TOOL,1
    SPINDL/RPM,100,CLW
    COOLNT/FLOOD
   &nbspAINT/COLOR,186
    RAPID
    GOTO/-127.6618,136.7055,30.0000,0.0000000,0.0000000,1.0000000
  
    RAPID
    GOTO/-127.6618,136.7055,2.5400
   &nbspAINT/COLOR,42
    FEDRAT/MMPM,36.0000
    GOTO/-126.2491,136.9759,2.1546
  
    GOTO/-124.6974,138.0341,1.6513
    GOTO/-123.6231,139.8295,1.0907
    GOTO/-123.4242,141.6971,0.5874
    GOTO/-123.9852,143.4896,0.0842
    GOTO/-125.2133,144.9106,-0.4191
    GOTO/-126.9056,145.7254,-0.9223

高

，长见识

建议给热心的ray斑竹加分鼓励

作者: zhangcanwei 时间: 2004-3-31 13:19
老大，多谢！我没权力给你加分，先在心里给你加分！！

作者: ROVER616 时间: 2004-4-2 14:49
use gpp 模拟仿真后生成。CL文件

   \Cimatron\CimatronE\Data\VERIFY_DIR

UNIT/MM
NEXT_TOOLPATH
NEXT_PROCEDURE
PPRINT/WCUT
PPRINT/No Text
CUTTER/10.0,0.0,0.0,0.0,0,0,15.0
LOADTL/1,ADJUST,1
FROM/-261.6953,0.0551,50.0
GOHOME
TOOLINF/'无名称',1,10.0,0.0,30.0,15.0,'无备注'
RAPID
SPINDL/RPM,1000,CLW
COOLNT/OFF
GOTO/-261.6953,0.0551,50.0,0.0,0.0,1.0 $$  TP=TP_MODEL-3 Proc. WCUT =3 Blk. =9
FEDRAT/150,MMPM
GOTO/-261.6953,0.0551,44.0,0.0,0.0,1.0 $$  TP=TP_MODEL-3 Proc. WCUT =3  Blk. =11
FEDRAT/500,MMPM
GOTO/-261.8747,0.1093,44.0,0.0,0.0,1.0 $$  TP=TP_MODEL-3 Proc. WCUT =3  Blk. =14
GOTO/-261.8748,-0.1082,44.0,0.0,0.0,1.0 $$  TP=TP_MODEL-3 Proc. WCUT =3  Blk. =15
GOTO/-261.5158,0.0015,44.0,0.0,0.0,1.0 $$  TP=TP_MODEL-3 Proc. WCUT =3  Blk. =16
GOTO/-261.6953,0.0551,44.0,0.0,0.0,1.0 $$  TP=TP_MODEL-3 Proc. WCUT =3  Blk. =17
GOTO/-259.9699,5.8016,44.0,0.0,0.0,1.0 $$  TP=TP_MODEL-3 Proc. WCUT =3  Blk. =19
CIRCLE/-245.9885,52.3684,44.0,0.0,0.0,-1.,48.6204
GOTO/-267.7817,8.9058,44.0 $$  TP=TP_MODEL-3 Proc. WCUT =3  Blk. =21
CIRCLE/180.6242,-0.2333,44.0,0.0,0.0,1.,448.499
GOTO/-267.7901,-8.9506,44.0 $$  TP=TP_MODEL-3 Proc. WCUT =3  Blk. =22
CIRCLE/-245.5723,-52.8128,44.0,0.0,0.0,-1.,49.1683
GOTO/-243.7371,-3.6787,44.0 $$  TP=TP_MODEL-3 Proc. WCUT =3  Blk. =23
GOTO/-237.4231,-3.7582,44.0,0.0,0.0,1.0 $$  TP=TP_MODEL-3 Proc. WCUT =3  Blk. =24

欢迎光临 iCAx开思网 (https://www.icax.org/)